Security: Video

This article explains how to use the settings as per the devices current configured capabilities if you just added a device to BVMS, you get the possible stream options as per a “Config table” known to BVMS.

With BVMS 11.0, new licensing system was introduced. Attached document describes how to migrate existing activated BVMS licenses from the Bosch Software License Manager System (SLMS) licensing system to the new Bosch Remote Portal licensing.

DIVAR IP units can be upgraded to BVMS 11.0. Starting with BVMS 11.0, the BVMS licensing scheme also applies to the DIVAR IP units. This document describes which units you can upgrade to BVMS 11.0 and which licenses you have to order for a DIVAR IP unit!

The article explains the different types of licenses, the basic rules of the license activation and how to activate licenses for the BVMS system.

Short intro and related topics: This article will review the settings required to configure Windows as a NTP time server. Note: If you are running VRM and have the Time Server enabled, you must disable the Time Server before performing the following. Article requirements: Windows Server 2016/ Windows 10

Starting with BVMS 10.0, ONVIF encoder events can be retrieved from VSG or ONVIF encoder directly. Additionally to ONVIF profile S, BVMS 10.0 supports ONVIF profile T.

It is possible to add ONVIF compliant cameras to Bosch Video Management System as live only devices or as VSG devices (then the cameras will also record). This article explains how to add an ONVIF camera as VSG device in full Bosch Video Management System (BVMS 10.1). We recommend using Bosch Workstations and Servers. They are fully tested and optimized for Bosch Video Management System.   Article requirements: BVMS installed ONVIF camera. Please refer to BVMS - ONVIF Device compatibility for additional information. PC/ Server/ Workstation

This article lists the initial troubleshooting steps and concrete instructions for collecting logging for issues with ONVIF cameras, added to BVMS system. We will classify the different issue scenarios one can have using ONVIF cameras in BVMS system. Depending on the issue the article lists the required logging to start initial troubleshooting.

What happens when you upgrade the SW of your Management Server form e.g. BVMS 10.0 to BVMS 10.1 and you have not prepared a BVMS 10.1 activation key beforehand?

Question Why I cannot see my camera in the Logical Tree from Operator Client? Answer Please make sure that you have done all the steps below accordingly. Normally, to be able to view a camera in the Operator Client, you need to: Go to the Maps and Structure tab from Configuration Client. Drag and drop the camera in question from the Device Tree to the Logical Tree. Save and Activate the changes. This step is very important because otherwise, you will not be able to see the changes in Operator Client, even though the first 2 steps were carried out in Configuration Client.

This article helps you to solve the situation where the "No Config" error message appears when you try to authenticate in Operator Client. This error can be persistent, no matter what central server you attempt to login to and no matter what user account or credentials you are trying to use. This means that you have a corrupt cache .dat file on your system. Follow the steps from this article if you attempt to login into BVMS Operator Client and encounter the message below and you want to fix it: "Please enter your credentials... No config..."

The "storage state failure" alarm doesn't always mean a recording error unless there is a gap at the time of the error for that camera that reported it. It is an error of the iSCSI protocol; it means that when the camera releases the connection for a certain block it has not received a response back from the iSCSI target in a certain time.

Logs are definitely important. We would even say they are the most important thing for a system to function properly. At some point, the Central Support Team may ask you to provide them with the BVMS Configuration Collection. This article explains you how and where you can get the BVMS Configuration Collection of your system.

Various overlays in the video image provide important status information. But what does mean the blinking play button near the yellow exclamation icon?

This article explains how to add new ONVIF cameras to a system that runs in full Bosch Video Management System (BVMS) via the Configuration Client. Depending on the license type you have installed in the Bosch Video Management System (BVMS), you can add a certain number and different types of cameras/ encoders.  BVMS supports 3rd party cameras as well, but they need to be compliant to ONVIF Profile S.

This guide is meant to help you adding new cameras in VRM in Configuration Client and display their images in Operator Client.

Operator Client helps you display the original full image circle of a panoramic camera, its image dewarped or you can select a point of interest of the image.

What should you do if you tried to drag an drop the device to the cameo window from BVMS Operator Client and instead having the video, it displays the logical tree?

You may have installed Configuration Manager on your PC, you tried to run it but the software no longer works. What could be the reason?

Follow the steps from this article if you want to configure your camera to detect motion and then send the event to the server, to start recording. This guide helps you set this option only for nights and weekends. It is important that you find the best possible motion detection settings for the camera in order to avoid unnecessary recordings or notifications.