Security: Video

This article explains how BVMS can be configured to connect to an LDAP (or Microsoft Active Directory) and use it as a base for user authentication.   BVMS is able to function in a (Windows) domain-controlled environment. The BVMS (and related) services run under the local system account. If another (domain-controlled) account is used to run these services, their permissions level should be the same as the local system account. It is recommended to add the Windows server to the domain first (as a domain member), before installing the BVMS software. The BVMS configuration is independent from the domain configuration, however, crucial changes in the domain could break the connection between the BVMS system and the LDAP authentication mechanism.

The Divar AN 3000/5000 features the ability to ping an IP address, thus allowing the technician to verify that the workstation that is to connect to the Divar can be seen on the network. Please note that this only checks the connection from the DIVAR to the Workstation. Ping operates by sending Internet Control Message Protocol (ICMP) echo request packets to the target host and waiting for an ICMP echo reply. The program reports errors, packet loss, and a statistical summary of the results.

This article will explain how to set-up the RAID quickly in order to start the "re-imaging" process from the Recovery DVD (one at DIVAR IP 6000 R2 - or two DVDs at DIVAR IP 7000 R2) enclose to each DIVAR IP 7000 R2 or DIVAR IP 6000 R2 delivery. 

The attached manual provides information for Mobile Video Service (MVS) within Bosch Video Management System. You can find:  - how to configure the router and Internet Information Service (IIS) - how to add MVS to BVMS - user guide - some troubleshooting tips   This document can also be found online here.

Sometimes it is preferable to have a different “user mode” during the day then in the night. Our cameras by default have the option to switch the user mode e.g. triggered by the camera D/N switch over. But also other triggers can be chosen. Below an example how to setup the “user mode” switching triggered by the D/N switch over.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.   Related Products: BVMS SDK, BVMS    Overview: Analyzing BVMS systems with SDK components is a challenging task, because the functionality and the runtime behavior of those systems are harder to determine than for a BVMS systems without SDK functionality. In order to troubleshoot BVMS systems with SDK components support needs the following information and logging. Please prove the following information to support:   Symptom specific Information   Problem Description SMA validity How to retrieve the Hardware ID for BVMS and check the Software Maintenance Agreement (SMA) status? BVMS stand alone or appliance Detailed description of the expected behavior of the SDK functionality. Detailed description of the actual behavior of the SDK functionality.   SDK Components What type is the standalone SDK application (based on ClientSDK, ServerSDK, or CameoSDK) and on which machine is it running? Are there additionally client scripts, server scripts or workstation startup scripts?   SDK Interactions Do SDK components interact with remote Operator Clients? Do SDK components interact with the Operator Client UI? Do SDK components control devices? How often are client scripts triggered? How often are scripts triggered by BVMS event?   Environment Which shared resources are accessed by SDK actions? (Dome cameras, AMG, Operator Client UI) Do SDK components interact with an unreliable environment? (Unstable network, offline devices, offline PCs, etc.) Do SDK components properly handle offline situations? (offline devices, configuration changes, etc.)    Logging Information Please provide the Scriplet and/or Log files The optimal approach is to provide both the scriplet and logging. ClientScript logfiles: can be found in the ConfigCollection of Operator Client machines. ServerScript logfiles: can be found in the ConfigColletion of Management Server machines.   Make sure that logging is implemented in the script and that logging is activated in the configuration.  

Perhaps you are wondering how to set the maximum retention time on a Divar Network? Some of our customers asked about this option. Well, in DIVAR Network and Hybrid there is not retention time. But you can set the automatically deleting time, that is more or less the same.   Step-by-step guide:   Open one Browser and type your device IP address Login with the administrator account Go to Settings > Storage > Recording Fill in the box with the desired automatic deletion time   Another option is to make this change directly in the local interface of the unit.

Short intro and related topics: This article will review the settings required to configure Windows as a NTP time server. Note: If you are running VRM and have the Time Server enabled, you must disable the Time Server before performing the following. Article requirements: Windows Server 2016/ Windows 10

Find below Gmail SMTP settings which you have to set in your EMAIL screen of DIVAR Menu. SMTP Server address: smtp.gmail.com Username: Your Gmail e-mail adress Password: Your Gmail password Port (TLS😞 587 Port (SSL😞 465 TLS / SSL required: Yes TLS : Transport Layer Security         SSL: Secure Sockets Layer What happens if you do not select either one? If neither SSL nor TLS is used , then the communication line can easily become a party line for eavesdroppers, all data transmitted between DIVAR and e-mail account for anyone to see.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.   Related Products: BVMS, Operator Client This article describes the initial information needed to start troubleshooting Operator Client Crash.   General Information   SMA validity How to retrieve the Hardware ID for BVMS and check the Software Maintenance Agreement (SMA) status? BVMS stand alone or appliance Detailed problem description   Symptom specific Information Problem Description   Note down the events that lead to crash Classify the crash reproducible crashes that trigger Windows Error Reporting crashes/ hangs/ freezes that are hard to reproduce, or take long before repeating   Logging Information   Dump file from the crash – refer to the following article How To create BVMS memory dump?  ConfigCollection from the machine where the crashing Operator Client is running.

Question   Why the Windows license key and System ID are the same on all my DIVAR IP 6000?   Answer   These units come pre-licensed from the factory and they have an OEM (Original Equipment Manufacturer) license activated. Please see more information about OEM on the Wikipedia link below:  https://en.wikipedia.org/wiki/Original_equipment_manufacturer According to its datasheet, all components relevant to the usage of DIVAR IP 6000 as storage array in a Bosch recording solution are pre-installed and preconfigured. Simply connect to the network and power the unit up — DIVAR IP 6000 is ready to begin recording straight out-of-the-box.

In Cloud-based Services, different 'Actions' can be configured for automatic processing as well as manual action for the operators (Alarm Agents). There are 2 different options how an action is processed: An 'Automatic Action' is processed automatically when the related Service Scenario is performed. An 'Intervention Action' is executed manually by an operator from the Cloud-based Service Operator Interface. This note shows available actions in Cloud-based Services and provides a step by step instruction to configure these actions.   Step-by-step guide   1. Send e-mail "Send e-mail" sends an e-mail notification to the configured recipient(s). The action can be used as manual action for the operators (Intervention Action). The content of the alarm email can be configured to the customer's needs.   To configure a "Send e-mail" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Email'. 6. Type recipients, CC's, mail subject and message. Use the pull down to enter environment variables to the e-mail text. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   2. Execute PTZ Command "Execute PTZ Command" starts an auxiliary command on a Pan-Tilt-Zoom (PTZ) camera. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Note the available auxiliary commands in the camera’s manual. To configure an "Execute PTZ Command" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Execute PTZ Command'. 6. Select PTZ camera, select auxiliary command and type the command No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing   3. Go to PTZ Preposition "Go to PTZ Preposition" moves a Pan-Tilt-Zoom (PTZ) camera to a preposition. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). The prepositions (shots) need to be configured via the Device Page upfront. To configure a "Go to PTZ Preposition" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Go to PTZ preposition'. 6. Select PTZ camera and type the preposition No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   4. Play Audio on Device "Play Audio on Device" replays an audio file directly from the device's loudspeaker. The action is intended to perform standard audio interventions without the need for the operator (alarm agent) to talk. "Play Audio on Device" can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Audio files need to be prepared and installed by CBS development. If you want to use your own audio files, please get in contact with technical support. To configure a "Play Audio on Device" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an Action. 5. Give the Action a descriptive name and select 'Play audio on device'. 6. Select the audio device and select the audio file. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   5. Switch Relay "Switch Relay" switches a relay of one or more IP devices. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). To configure a "Switch Relay" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Relay'. 6. Select activation mode and select one or more relays to switch. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   6. Notify Monitoring Center and Log Event Both action types "Notify Monitoring Center" and "Log Event" are obsolete and can not be used in a Service Scenario.  See also: How to add a user to Remote Alert service in Remote Portal?

Question   Where can you find the ISO image for recovery of DIVAR IP 7000R2 and DIVAR IP 6000R2?   Answer   Related Products: DIVAR IP 7000R2 and DIVAR IP 6000R2   CTN Description   DIP-6180-00N  DIVAR IP 6000 2U W/O HDD  DIP-6183-4HD  DIVAR IP 6000 2U 4X3TB  DIP-6183-8HD  DIVAR IP 6000 2U 8X3TB  DIP-6184-4HD  DIVAR IP 6000 2U 4X4TB  DIP-6184-8HD  DIVAR IP 6000 2U 8X4TB  DIP-61F0-00N  DIVAR IP 6000 3U W/O HDD  DIP-61F3-16HD  DIVAR IP 6000 3U 16X3TB  DIP-61F4-16HD  DIVAR IP 6000 3U 16X4TB  DIP-7180-00N  DIVAR IP 7000 2U W/O HDD (R2)  DIP-7183-4HD  DIVAR IP 7000 2U 4X3TB (R2)  DIP-7183-8HD  DIVAR IP 7000 2U 8X3TB (R2)  DIP-7184-4HD  DIVAR IP 7000 2U 8X3TB (R2)  DIP-7184-8HD  DIVAR IP 7000 2U 8X4TB (R2)  DIP-71F0-00N  DIVAR IP 7000 3U W/O HDD (R2)  DIP-71F3-16HD  DIVAR IP 7000 3U 16X3TB (R2)  DIP-6704-HD 4000GB HDD DIVAR IP 6000/7000    For recovery of DIVAR IP 6000 R2 or DIVAR IP 7000 R2 one should use only the DVD provided with the particular device. Do not use the DVD for recovery if you are not sure that it is the one delivered with the system. In case the DVD is lost or damaged request the respective ISO image from Bosch Technical Support.  Solution:  Request the ISO image from Bosch Technical Support:   Provide the Serial Number of the device Issue description: What is the reason for the recovery Why it is not possible to use the recovery DVD   Note: This article will guide you through the recovery steps of a DIP:  TSG: Rebuild broken OS RAiD on DIVAR IP 6000, DIVAR IP 6000 R2, DIVAR IP 7000, DIVAR IP 7000 R2

Related Products Workstations, Z4G4, Microsoft License Question Is it possible to Activate Windows 10 by phone for Bosch Workstations? Answer With introduction of Windows 10, Microsoft disable the phone license activation for Bosch Workstations. Please perform online activation over internet.

Related Products: BVMS / MVS / VSDK Overview: On request from development to provide a dump file from MVS system please follow the steps in the solution section.   Step-by-step guide   Reproduce the issue Download the Microsoft debugger procdump (https://technet.microsoft.com/en-us/sysinternals/dd996900.aspx). The procdump tool is also attaced to the article :How To create BVMS memory dump?  When application is crashing, do not click any buttons on the appeared error window that will change the program state. Run the procdump.exe from the directory where you copied the tool with following command line (Start - cmd): procdump.exe –ma <name of the programm exe> <dump file name>.dmp   In the case of MVS you need to do that for all 4 MVS services: - Bosch.MVS.SourceProvider.BVMS.Service.exe - Bosch.MVS.DataStorage.Service.exe - Bosch.MVS.SourceProvider.MobileCamera.Service.exe - Bosch.MVS.Transcoder.Service.exe

The Windows Storage Server operating system of DIVAR IP all-in-one 7000 is installed on a two SSD drives in redundant (mirrored) configuration. Health status of the mirrored OS drives can be monitored using a tool called Virtual RAID on CPU (formerly known as Rapid Storage Technology). Installation and configuration steps are described below. Step-by-step guide   1. Installation: Download the setup from here Copy the content to a USB drive When the BVMS default screen is shown, press CTRL + ALT + DEL Hold down the SHIFT key while clicking Log off Log in as BVRAdmin Transfer the IATA_CD.exe from the USB drive to the BVRAdmin desktop Double click the IATA_CD.exe executable Follow the installation procedure as shown in the screen shots     2. Email notification: Note: The E-mail notification feature is based on SMTP access without authentication. It is strongly suggested to use this functionality only with a dedicated server in the local network, which is specifically configured for this purpose and doesn’t handle any critical data.

If you want to control the camera from a DIVAR wired through a VJD 3000, you have to configure the VJD and the DIVAR as well. Below you will find the steps which will help you to set up your devices.

Question Why I cannot see my camera in the Logical Tree from Operator Client? Answer Please make sure that you have done all the steps below accordingly. Normally, to be able to view a camera in the Operator Client, you need to: Go to the Maps and Structure tab from Configuration Client. Drag and drop the camera in question from the Device Tree to the Logical Tree. Save and Activate the changes. This step is very important because otherwise, you will not be able to see the changes in Operator Client, even though the first 2 steps were carried out in Configuration Client.