Security: Video

What happens when you upgrade the SW of your Management Server form e.g. BVMS 10.0 to BVMS 10.1 and you have not prepared a BVMS 10.1 activation key beforehand?

Preventing condensation on security cameras is crucial because it can obstruct the camera's view, affecting its ability to capture clear footage. Over time, moisture build-up can potentially damage the internal components of the camera, affecting its functionality and lifespan

‘Status 11’ means that the wiper is blocked and cannot move freely or cannot move at all. Please check if the wiper is working properly and can move freely.

This article explains how to configure the Bosch ITS and NTCIP licensed versions of IP moving cameras to respond to National Transportation Communications ITS Protocol (NTCIP).

This article contains the options for physical/ default reset of Bosch Inteox cameras.

The maximum zoom speed in the GUI is operational but is only applicable during "manual control." When the operator calls for 30x, the zoom speed has to remain constant. While the speed may not be as rapid as anticipated, it is essential to understand that this camera model is already operating at its optimum capacity.

The RCPP command to enable/ disable the privacy masks is CONF_PRIV_MSK_POLY - 0x0bd8. Follow this article to see the rcpp command to enable & disable the privacy mask of a Bosch camera (moving or fixed).

Operator Client helps you display the original full image circle of a panoramic camera, its image dewarped or you can select a point of interest of the image.

Bosch requires the installer to provide the specified power mentioned on the product spec sheet and labels. While taking into consideration the POE standards. Bosch doesn't support out-of-spec operation of our cameras as we cannot guarantee proper functionality in such circumstances. Thus, we will not be providing out-of-spec voltage or power values at this stage.

In the winter period, if there is no PAN functionality in the camera and despite this, the TILT still works, this could be caused by the snow or ice that might be stuck between the static part of the camera and the moving camera head. Find out from this article how you can prevent this happening.

Waiting For Power - Invalid PoE source was detected during the auto-negotiation. The Pan Motor, Tilt motor, and the heaters will be disabled.

Please note that the relay output of the IO Alarm card is a dry contact relay (with 24VAC/VDC, 5 A). In order to control another circuit that has a 230V you can't do that directly because its higher than it was design for. In order to safety control a 230V, you could use a 24V on that output and control an additional/external relay: powering its coil this relay could switch the 230 circuit of the washer.

For certain conditions, MIC cameras will display status codes on the video image. What does "status 9" mean on the MIC IP ultra 7100i │ MIC IP starlight 7100i camera's web page ?

Be sure that the MIC-7100i camera is configured in BVMS Configuration Client with "Bosch-AutoDome Bilinx" protocol and not with "Bosch-AutoDome" protocol or other options from the list.

This is a known design limitation and has always been present in the mentioned platforms. There are also no plans to correct this behavior.

This article provides possible causes and solutions regarding FLEXIDOME Inteox 7100i (CPP13) - calibration lost using FW 8.45.0032.

The privacy mask moves around with the image when the MIC IP starlight 7000 HD camera is in PTZ mode. The camera is integrated into a 3rd party Software.

This article presents what are the limitations of Privacy overlay in BVMS 12 (Pano cameras, h.263 & MPEG, decoder, VSC).

Milestone search tools (People & Vehicles) find results for other cameras. But the Bosch Forensic Search Agent finds zero results for DINION IP starlight 7000 FW v7.89. Why?

The "Lens rotation" slider can be used to correct for any manual lens rotations performed during installation. If the lens is manually rotated during installation, the slider value should be aligned with the rotation value shown on the lens.