Security: Video

If BVMS and VRM are installed on the same machine, it is needed to change the TCP Port of the VRM Monitor.

This article explains how BVMS can be configured to connect to an LDAP (or Microsoft Active Directory) and use it as a base for user authentication.   BVMS is able to function in a (Windows) domain-controlled environment. The BVMS (and related) services run under the local system account. If another (domain-controlled) account is used to run these services, their permissions level should be the same as the local system account. It is recommended to add the Windows server to the domain first (as a domain member), before installing the BVMS software. The BVMS configuration is independent from the domain configuration, however, crucial changes in the domain could break the connection between the BVMS system and the LDAP authentication mechanism.

The Divar AN 3000/5000 features the ability to ping an IP address, thus allowing the technician to verify that the workstation that is to connect to the Divar can be seen on the network. Please note that this only checks the connection from the DIVAR to the Workstation. Ping operates by sending Internet Control Message Protocol (ICMP) echo request packets to the target host and waiting for an ICMP echo reply. The program reports errors, packet loss, and a statistical summary of the results.

This article will explain how to set-up the RAID quickly in order to start the "re-imaging" process from the Recovery DVD (one at DIVAR IP 6000 R2 - or two DVDs at DIVAR IP 7000 R2) enclose to each DIVAR IP 7000 R2 or DIVAR IP 6000 R2 delivery. 

Relates to: IP Storage/PC HW - DIVAR IP 6000 R2 and DIVAR IP 7000 R2 Both DIVAR IP units running the BIOS from American Megatrends Inc. (A.M.I) There are PRE BOOT or POST BOOT beeps. Please see the following Acoustic Error Codes.

The attached manual provides information for Mobile Video Service (MVS) within Bosch Video Management System. You can find:  - how to configure the router and Internet Information Service (IIS) - how to add MVS to BVMS - user guide - some troubleshooting tips   This document can also be found online here.

This article explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below: Simple integration using direct connectivity to analog monitor and joystick, typically found in single camera installation (for example, mobile surveillance vehicles) Integration into an existing analog matrix switcher typically found in large installations (such as for city surveillance)

An object moving or a low/ higher contrast scene can throw off the autofocus option, resulting in a soft focus or even not focus at all. Using manual focus is an obvious solution, but manual focus isn’t exactly easy to get sharp images. Manual focus requires a bit of know-how and some practice to get right. If you would like to improve the performance and get a sharp image, please see below how you can manually adjust the focus ring on a Dinion Thermal camera.

Sometimes it is preferable to have a different “user mode” during the day then in the night. Our cameras by default have the option to switch the user mode e.g. triggered by the camera D/N switch over. But also other triggers can be chosen. Below an example how to setup the “user mode” switching triggered by the D/N switch over.

Some options have been removed when compared to previous CPPs, as they are only useful for moving cameras. Find here the overview of the web page of ‘Live’ functions section and the options remained available for FLEXIDOME multi 7000i (CPP14) cameras.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.   Related Products: BVMS SDK, BVMS    Overview: Analyzing BVMS systems with SDK components is a challenging task, because the functionality and the runtime behavior of those systems are harder to determine than for a BVMS systems without SDK functionality. In order to troubleshoot BVMS systems with SDK components support needs the following information and logging. Please prove the following information to support:   Symptom specific Information   Problem Description SMA validity How to retrieve the Hardware ID for BVMS and check the Software Maintenance Agreement (SMA) status? BVMS stand alone or appliance Detailed description of the expected behavior of the SDK functionality. Detailed description of the actual behavior of the SDK functionality.   SDK Components What type is the standalone SDK application (based on ClientSDK, ServerSDK, or CameoSDK) and on which machine is it running? Are there additionally client scripts, server scripts or workstation startup scripts?   SDK Interactions Do SDK components interact with remote Operator Clients? Do SDK components interact with the Operator Client UI? Do SDK components control devices? How often are client scripts triggered? How often are scripts triggered by BVMS event?   Environment Which shared resources are accessed by SDK actions? (Dome cameras, AMG, Operator Client UI) Do SDK components interact with an unreliable environment? (Unstable network, offline devices, offline PCs, etc.) Do SDK components properly handle offline situations? (offline devices, configuration changes, etc.)    Logging Information Please provide the Scriplet and/or Log files The optimal approach is to provide both the scriplet and logging. ClientScript logfiles: can be found in the ConfigCollection of Operator Client machines. ServerScript logfiles: can be found in the ConfigColletion of Management Server machines.   Make sure that logging is implemented in the script and that logging is activated in the configuration.  

Question Why the Autodome 7000i INTEOX cannot connect to the S&ST Cloud services?   Answer Most likely, when you tried to connect to the S&ST ecosystem, you missed one of the steps explained in this article: How to connect a Bosch INTEOX camera to S&ST using Configuration Manager?   If you are sure that you have followed correctly the steps from the article above, please collect from camera: Diagnostics logs Config file with log in credentials Event logs How to collect logs from your Bosch IP Camera/Encoder? Please check if the the following message is displayed in the logs: ✅ Tip "Not connecting (CC enabled: true; Network connection: true; MQTT client ready: true; NTP enabled: false)" → this indicates that you didn't turn on the NTP which is a prerequisite to connect to the cloud back-end  Please enable the timeserver and make sure the time of the camera is synchronized with a public time-server when connecting to the S&ST cloud.   Note: NTP synchronization is necessary if the camera is going to be claimed in the portal. Please refer also to the Help & Support page:  Claiming cameras

Perhaps you are wondering how to set the maximum retention time on a Divar Network? Some of our customers asked about this option. Well, in DIVAR Network and Hybrid there is not retention time. But you can set the automatically deleting time, that is more or less the same.   Step-by-step guide:   Open one Browser and type your device IP address Login with the administrator account Go to Settings > Storage > Recording Fill in the box with the desired automatic deletion time   Another option is to make this change directly in the local interface of the unit.

Short intro and related topics: This article will review the settings required to configure Windows as a NTP time server. Note: If you are running VRM and have the Time Server enabled, you must disable the Time Server before performing the following. Article requirements: Windows Server 2016/ Windows 10

Find below Gmail SMTP settings which you have to set in your EMAIL screen of DIVAR Menu. SMTP Server address: smtp.gmail.com Username: Your Gmail e-mail adress Password: Your Gmail password Port (TLS😞 587 Port (SSL😞 465 TLS / SSL required: Yes TLS : Transport Layer Security         SSL: Secure Sockets Layer What happens if you do not select either one? If neither SSL nor TLS is used , then the communication line can easily become a party line for eavesdroppers, all data transmitted between DIVAR and e-mail account for anyone to see.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.

In order to quickly offer a technical solution or to provide a professional advice for the next analysis steps, the technical support specialists need to get some general and basic information. Ticket content should always be in English and provided in a well summarized and structured way in order to be able to provide a quick and appropriate feedback. Not following the guideline will impact the processing time of the ticket.   Related Products: BVMS, Operator Client This article describes the initial information needed to start troubleshooting Operator Client Crash.   General Information   SMA validity How to retrieve the Hardware ID for BVMS and check the Software Maintenance Agreement (SMA) status? BVMS stand alone or appliance Detailed problem description   Symptom specific Information Problem Description   Note down the events that lead to crash Classify the crash reproducible crashes that trigger Windows Error Reporting crashes/ hangs/ freezes that are hard to reproduce, or take long before repeating   Logging Information   Dump file from the crash – refer to the following article How To create BVMS memory dump?  ConfigCollection from the machine where the crashing Operator Client is running.

Question   Why the Windows license key and System ID are the same on all my DIVAR IP 6000?   Answer   These units come pre-licensed from the factory and they have an OEM (Original Equipment Manufacturer) license activated. Please see more information about OEM on the Wikipedia link below:  https://en.wikipedia.org/wiki/Original_equipment_manufacturer According to its datasheet, all components relevant to the usage of DIVAR IP 6000 as storage array in a Bosch recording solution are pre-installed and preconfigured. Simply connect to the network and power the unit up — DIVAR IP 6000 is ready to begin recording straight out-of-the-box.

In Cloud-based Services, different 'Actions' can be configured for automatic processing as well as manual action for the operators (Alarm Agents). There are 2 different options how an action is processed: An 'Automatic Action' is processed automatically when the related Service Scenario is performed. An 'Intervention Action' is executed manually by an operator from the Cloud-based Service Operator Interface. This note shows available actions in Cloud-based Services and provides a step by step instruction to configure these actions.   Step-by-step guide   1. Send e-mail "Send e-mail" sends an e-mail notification to the configured recipient(s). The action can be used as manual action for the operators (Intervention Action). The content of the alarm email can be configured to the customer's needs.   To configure a "Send e-mail" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Email'. 6. Type recipients, CC's, mail subject and message. Use the pull down to enter environment variables to the e-mail text. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   2. Execute PTZ Command "Execute PTZ Command" starts an auxiliary command on a Pan-Tilt-Zoom (PTZ) camera. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Note the available auxiliary commands in the camera’s manual. To configure an "Execute PTZ Command" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Execute PTZ Command'. 6. Select PTZ camera, select auxiliary command and type the command No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing   3. Go to PTZ Preposition "Go to PTZ Preposition" moves a Pan-Tilt-Zoom (PTZ) camera to a preposition. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). The prepositions (shots) need to be configured via the Device Page upfront. To configure a "Go to PTZ Preposition" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Go to PTZ preposition'. 6. Select PTZ camera and type the preposition No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   4. Play Audio on Device "Play Audio on Device" replays an audio file directly from the device's loudspeaker. The action is intended to perform standard audio interventions without the need for the operator (alarm agent) to talk. "Play Audio on Device" can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Audio files need to be prepared and installed by CBS development. If you want to use your own audio files, please get in contact with technical support. To configure a "Play Audio on Device" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an Action. 5. Give the Action a descriptive name and select 'Play audio on device'. 6. Select the audio device and select the audio file. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   5. Switch Relay "Switch Relay" switches a relay of one or more IP devices. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). To configure a "Switch Relay" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Relay'. 6. Select activation mode and select one or more relays to switch. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   6. Notify Monitoring Center and Log Event Both action types "Notify Monitoring Center" and "Log Event" are obsolete and can not be used in a Service Scenario.  See also: How to add a user to Remote Alert service in Remote Portal?

Question   Where can you find the ISO image for recovery of DIVAR IP 7000R2 and DIVAR IP 6000R2?   Answer   Related Products: DIVAR IP 7000R2 and DIVAR IP 6000R2   CTN Description   DIP-6180-00N  DIVAR IP 6000 2U W/O HDD  DIP-6183-4HD  DIVAR IP 6000 2U 4X3TB  DIP-6183-8HD  DIVAR IP 6000 2U 8X3TB  DIP-6184-4HD  DIVAR IP 6000 2U 4X4TB  DIP-6184-8HD  DIVAR IP 6000 2U 8X4TB  DIP-61F0-00N  DIVAR IP 6000 3U W/O HDD  DIP-61F3-16HD  DIVAR IP 6000 3U 16X3TB  DIP-61F4-16HD  DIVAR IP 6000 3U 16X4TB  DIP-7180-00N  DIVAR IP 7000 2U W/O HDD (R2)  DIP-7183-4HD  DIVAR IP 7000 2U 4X3TB (R2)  DIP-7183-8HD  DIVAR IP 7000 2U 8X3TB (R2)  DIP-7184-4HD  DIVAR IP 7000 2U 8X3TB (R2)  DIP-7184-8HD  DIVAR IP 7000 2U 8X4TB (R2)  DIP-71F0-00N  DIVAR IP 7000 3U W/O HDD (R2)  DIP-71F3-16HD  DIVAR IP 7000 3U 16X3TB (R2)  DIP-6704-HD 4000GB HDD DIVAR IP 6000/7000    For recovery of DIVAR IP 6000 R2 or DIVAR IP 7000 R2 one should use only the DVD provided with the particular device. Do not use the DVD for recovery if you are not sure that it is the one delivered with the system. In case the DVD is lost or damaged request the respective ISO image from Bosch Technical Support.  Solution:  Request the ISO image from Bosch Technical Support:   Provide the Serial Number of the device Issue description: What is the reason for the recovery Why it is not possible to use the recovery DVD   Note: This article will guide you through the recovery steps of a DIP:  TSG: Rebuild broken OS RAiD on DIVAR IP 6000, DIVAR IP 6000 R2, DIVAR IP 7000, DIVAR IP 7000 R2