Security: Video

Bosch requires the installer to provide the specified power mentioned on the product spec sheet and labels. While taking into consideration the POE standards. Bosch doesn't support out-of-spec operation of our cameras as we cannot guarantee proper functionality in such circumstances. Thus, we will not be providing out-of-spec voltage or power values at this stage.

In the winter period, if there is no PAN functionality in the camera and despite this, the TILT still works, this could be caused by the snow or ice that might be stuck between the static part of the camera and the moving camera head. Find out from this article how you can prevent this happening.

Waiting For Power - Invalid PoE source was detected during the auto-negotiation. The Pan Motor, Tilt motor, and the heaters will be disabled.

Please note that the relay output of the IO Alarm card is a dry contact relay (with 24VAC/VDC, 5 A). In order to control another circuit that has a 230V you can't do that directly because its higher than it was design for. In order to safety control a 230V, you could use a 24V on that output and control an additional/external relay: powering its coil this relay could switch the 230 circuit of the washer.

Be sure that the MIC-7100i camera is configured in BVMS Configuration Client with "Bosch-AutoDome Bilinx" protocol and not with "Bosch-AutoDome" protocol or other options from the list.

This is a known design limitation and has always been present in the mentioned platforms. There are also no plans to correct this behavior.

This article provides possible causes and solutions regarding FLEXIDOME Inteox 7100i (CPP13) - calibration lost using FW 8.45.0032.

The privacy mask moves around with the image when the MIC IP starlight 7000 HD camera is in PTZ mode. The camera is integrated into a 3rd party Software.

This article presents what are the limitations of Privacy overlay in BVMS 12 (Pano cameras, h.263 & MPEG, decoder, VSC).

The Image Stabilization cannot be used in combination with VCA tasks, with the various MIC-7100i models. Turning Off the image stabilization will solve this behavior.

We found that there was a change in the way intelligent tracking worked after CPP 7.3 firmware v7.62.0005. With these changes if an object triggered an alarm that turned on intelligent tracking, the camera would not track the object. It would wait for another object to trigger an alarm to track it.

The inconsistency in the tamper detection functionality could be due to various factors. Follow this article for more details.

Intelligent Video Analytics (IVA) Pro provides application-specific packages for building security and operations (IVA Pro Buildings), perimeter security (IVA Pro Perimeter), and traffic monitoring (IVA Pro Traffic). While some of the IVA Pro variants are included by default on supported cameras, others can be added via licenses. This article is dedicated to describing the license process in full.

Unsupported camera model: Auto-calibration is currently not supported for this camera model. Calibration could produce wrong results or might not work. Why is this message displayed in Configuration Manager?

This article presents solution regarding how to stop "rtp.p_type 97" (OSD or Video Authetication packet) on a CPP4 and CPP7.3  

Do not upgrade the camera FW directly to 7.81. Otherwise, “error 13: device check failed” message will be displayed, and the FW will not be upgraded successfully.

This article gives an overview of CPPs that correspond to certain types of cameras, decoders and encoders.

ONVIF control of the thermal DZ was never planned for the MIC-9000i in the launch of the product. However, you can get the Pan and Tilt via ONVIF Device Manager to work by enabling the PTZ configuration of the stream. 

With fw7.70 a new feature was introduced that allows you to tune the scene for Day and Night separately using 2 custom scene modes. This article explains how to switch the scene modes Custom mode#1 & Custom mode#2 based on Day or Night for Bosch cameras

This Authorization Letter is applicable for all Bosch Security and Safety products & software when a password reset for them is requested by customers, system integrators or by a local sales representative.