Security: Video

Find out from this article what is the domain name used to connect your DIVAR to the Remote Portal

Camera Counter Reports are available on Bosch IP cameras capable of Essential Video Analytics or Intelligent Video Analytics, which are connected directly to the Remote Portal.

FW 11.50.2 must be used for Single Controllers and 11.60.2 for Dual Controllers

 This article shows the keyboard shortcuts that can be used by operators when operating the BVMS system. 

The Divar AN 3000/5000 features the ability to ping an IP address, thus allowing the technician to verify that the workstation that is to connect to the Divar can be seen on the network. Please note that this only checks the connection from the DIVAR to the Workstation. Ping operates by sending Internet Control Message Protocol (ICMP) echo request packets to the target host and waiting for an ICMP echo reply. The program reports errors, packet loss, and a statistical summary of the results.

A password prevents unauthorized access to the device. You can use different authorization levels to limit access. Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. Therefore, you must always start from the highest authorization level when assigning passwords. This article will guide you step by step to set the destination password for decoders.

If one of DIVARs IP 5000 AIO is selected on a user profile, the Operator Client opens the site and works fine. One message is displayed when two or more DIVARs are added into the same Enterprise system.   If you already have a DIP 5000 AIO into your Enterprise system and you want to add additional units but you receive the following message, you can solve this by using the steps below: "Server of configuration database is already in the server list. Remove either the server that is twice in the list or make sure that the configuration database is not cloned between servers."

Our portfolio contains quite a variety of (mobile) video clients and applications. To get a fast first overview we created the attached table to compare the most important ones.

This article contains a step-by-step guide which explains how you can perform a full factory default of DSA E2800 via SANtricity Storage Manager by using Script Editor

Please check which port and protocol have been set on the camera that has the live black image.

This guide is meant to explain how to enable the appropriate debug commands for logging during random reboot situations, and which logging to collect for troubleshooting, as in general there are multiple triggers that can cause a device to reboot. The information gathered will help to analyze the root cause.  Please make sure that all of the logs collected cover the same time period.

This article describes the absolute minimum information we need in order to start analyzing and optimizing Video Analytics performance

This script will make your encoder to toggle relay 1 only when IVA rule #1 alarm is active.

Have a look in this article to learn how you can add ONVIF cameras to Configuration Manager through VSG managed by VRM.

Operator Client helps you display the original full image circle of a panoramic camera, its image dewarped or you can select a point of interest of the image.

To access the "Reset" options of a DIVAR IP 2000 Recording Appliance, you have to open the Appliance's "Dashboard".

This article contains videos which explain the usage of Bosch cameras integrated in Genetec Security Center.

This article presents possible causes and solution regarding no recording for cameras added to VRM (DIP 7000AIO): ‘Unexpected error’ in BVMS Config Client

  Important note Currently, the VRM is itself very seldom used in combination with Genetec. Starting with 2022, Genetec developed a new driver for Bosch cameras “Hybrid driver for CPP13/14+”. With this, the VRM is not considered anymore. With the old “Legacy (CPP7.3 and older) the VRM is still supported.      Related Products: VRM, Genetec Security Center Overview: It is possible to use VRM free of charge (no extra VRM license is required) within Genetec Security Center. Genetec is sending encrypted secret to the VRM server with the number of the licensed channels. When VRM receives and validates this, it can be used for that number of channels for 24 h. A periodic license update is send by Genetec, so the VRM licensing is guaranteed as long as it is used with Genetec Security Center. Default settings, if not extra configuration is needed or done. -License for 1000 Cameras - License update is done every hour   How to license more than 1000 cameras or change the license update period for VRM within Genetec Security Center: Open the Config Tool and Launch a Video Task Select the Archiver Go to the Resource Tab and click on Extensions From the Tab Installed extensions select Bosch. In the Tab VRM add a new VRM and/or select already configured VRM. Click on Advanced settings and add the following parameters If you need to license the system with more than the default 1000 licenses – create the parameter with Name VrmLicenseRequestCount and as value put the required number of licenses. The parameter name is case sensitive If you need to change the duration of the period between each license request (there is always one license request when the archiver starts) – create the parameter with Name VrmLicenseRequestPeriod. The duration of the period is in milliseconds. The default value is one hour. If the value is set to 0, the license request are disabled. The parameter name is case sensitive     Press Enter to confirm the entry and then Close Press Apply and then OK. At the webpage of the VRM one can check if the number of licenses is changed. If you would like to know how to replay the recordings from a Bosch camera managed by Bosch Video Recording Manager (VRM) in Genetec Security Center software, please follow this video: How to use VRM recording in Genetec Security Center   Note:  To support customer needs and to leverage the most important features of Bosch cameras (like data security, Video Analytics, and intelligent bitrate management), the agreed focus of Bosch and Genetec is on the Genetec Archiver Recording Solution. Current and future developments are focused on this recording solution and the VRM in Genetec will only be supported to maintain existing and upcoming projects where a VRM solution is selected. There will be no development of new features. In this maintenance mode, the following is possible: • Certification of new VRM versions (for projects)* • Certification of new DIVAR IP’s* *Requirement: stable API on VRM side Note: The VRM itself might offer more functionality not covered with the integration in Genetec.

This article lists different ways to connect to cameras Live/Playback using the Video Security Client/App: to DIVAR IP AIO/BVMS system or to Camera directly, bypassing DIVAR IP AIO/BVMS system.