Security: Video

Collection of FAQs for the Video IT Products DIP 6000 & 7000 R2, DIVAR IP AIO 5000/ 7000, DIVAR IP all-in-one 7000 (gen 3), DSA E2700 (EOL), DSA E2800, HP Workstations, HPE Servers

Whenever a central NTP Server is available the recommendation is to synchronize all cameras against the NTP central server.

Please keep in mind that for SNMP v3 only the the Standard MIB II file is supported. This means that only general network device performance monitoring parameters can be requested. There is no Bosch Private MIB II extension for SNMP v3. 

A network management server can poll the health status of a device via SNMP requests. This article shows how to configure Bosch cameras in order to be able to answer to such requests.

The default Community Strings for Bosch cameras is - public. To change it, please follow the steps below.

This article describes all the steps that will help you to create iSCSI Virtual Disk/LUNs after replacing an HDD on a DIVAR IP 5000 AIO.

Video Recording Manger v4.00.0070 does not allow anyone not configured in VRM, only as an admin (using Configuration Manager), to log into the VRM Monitor page.

This article explains briefly the basics of SNMP. Declares the basic terms of the protocol. It also explains what part of the protocol is supported by Bosch cameras.

Starting with BVMS 11.0, the license activation is done via Bosch Remote Portal. A transfer of the license from the Bosch Software License Manager System (SLMS) to the Bosch Remote Portal is required for every BVMS system to be upgraded from 10.1 to 11.0

This article explains how to use the settings as per the devices current configured capabilities if you just added a device to BVMS, you get the possible stream options as per a “Config table” known to BVMS.

This article explains how to fix the behavior of MIC IP 7000i/9000i Bosch camera when is out of focus during a rapid zoom

This article provides a step-by-step guide about how you can disable UPnP of Bosch IP cameras & multicast scan from Configuration Manager. One of the reason why UPnP (Universal Plug and Play) is enabled in our devices is because ONVIF uses this to scan the ONVIF device in the network.

This camera does not have the auto-focus functionality in the same sense as Autodome / Mic cameras.

*Firmware 9.10 must be installed prior to installation of this firmware 9.51. Firmware download location: Download Store or on the product page > Downloads: VIDEOJET decoder 8000 page

.NET Framework is the original implementation of .NET. It supports running websites, services, desktop apps, and more on Windows. The system requirements for Configuration Manager state .NET 4.7.2 as necessary to be installed. Configuration Manager v7.30 installation package does not provide .NET Framework 4.7.2.

Bosch Remote Portal connects you to your Bosch Security devices from anywhere and lets you perform remote administration and maintenance anytime

Depending on the 3rd party cameras’ capabilities, there are different ways of adding cameras to Bosch Alarm Management.

Possible causes and solution(s) Cameras which get connected from the customer's site to Bosch Remote Portal use an outgoing connection via TCP port 42000. Outgoing connections usually are not blocked by a router, however in a corporate network with proxy server, firewall, etc. involved, the IT department might open the needed ports. The troubleshooting steps below might help you to connect cameras to Bosch Remote Portal.   Known issues on camera commissioning In most cases when camera commissioning fails, the root cause is: No connection to Bosch Security Cloud from the customer’s site Blocked Internet connectivity (e.g. blocked ports by proxy or firewall) User belongs to more than one Company in Remote Portal The camera is already commissioned to a different cloud instance Known camera firmware issues Known camera date issue Further…  

This article explains how you can collect VRM logs in different versions of it

The browser supported by Bosch cameras depends on the CPP that camera belongs to and on the Firmware version the camera has.. In web browsers that do not support MPEG-ActiveX, VCA configuration is only possible via Configuration Manager.