Find attached the French version of this article!
🕞 This procedure takes in average ~ 10 min to complete
This information may be requested by Central Technical Support Team, as the bundle file is useful for troubleshooting the improper behavior of the unit.
The method for collecting the NetApp DSA E2800 support bundle file from SANtricity Storage Manager App is provided below.
Step-by-step guide
Please make sure that you have the SANtricity Storage Manager App installed on your unit.
1. Open the SANtricity Storage Manager App
2. Right click on your DSA E2800 > select "Execute Script..." option
3. Add the following line in the Script Editor: save storageArray supportData file="c:\supdat.7z" force=true;
4. Go to Tools and select "Verify Syntax"
5. "Syntax check complete" message should be displayed
6. Next, go to Tools and select "Execute Only"
7. To perform this operation, you have to login with your DSA E2800 credentials > click OK > "Working" message will be displayed
Note: it may take a while for the next window to appear
8. Select "Add Security Exception" and next "Confirm Security Exception"
9. You will be prompted to enter the credentials again. Fill in the necessary details and click OK
10. The Script will start the execution and the bundle file will be exported.
11. The file will be downloaded in "C:\"
Nice to know:
How to download the support bundle file for DSA E2800 via WEB browser?
How to download the support bundle file for DSA E-Series E2700?
You can also see the NetApp Knowledge Base: How to collect an E-Series support bundle via SANtricity command line interface
Note: You should have a NetApp account to access the NetApp KB article above.
This article explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below:
Simple integration using direct connectivity to analog monitor and joystick, typically found in single camera installation (for example, mobile surveillance vehicles)
Integration into an existing analog matrix switcher typically found in large installations (such as for city surveillance)
MegaRAID Storage Manager software automatically rebuilds the RAID 5 on a DIVAR IP unit without data loss. The rebuild is a fully automatic process, so it is not necessary to issue a Rebuild command. You can also monitor the progress of drive rebuilds.
Once the chassis was replaced and the drives were mounted in drive carriers, follow this step-by-step guide in order to rebuild RAID 5 on a DIVAR IP.
This article it is about analog control system connected directly to the MIC IP serial port. The serial com ports of traditional analog systems head end control systems connect directly to the RS485 input of the MIC IP models listed within this article.
When the camera operates in automatic Night-Mode and the switching interval is too fast the camera built in protection mechanism will intervene to prevent premature wear of the mechanical IR-Cut filter.
Check this article and find out what you can do if you are using one Divar network 2000 and you have a new Flexidome IP 5000i IR camera, but you cannot add it to the Divar because it is not displayed in “Detection” > “Device search” screen.
“Server is not online” message is displayed when accessing BVMS Operator Client. After clicking OK, the Operator Client is opening in a loop and never stops. What should you do?
The purpose of this article is to provide the step-by-step process of adding drives to a DIVAR IP 7000 R1 (DIP-7080-00N) Recording appliance and configure initial RAID setup on it.
This article presents possible causes and solution regarding no recording for cameras added to VRM (DIP 7000AIO): ‘Unexpected error’ in BVMS Config Client
For certain conditions, MIC cameras will display status codes on the video image.
What does "status 9" mean on the MIC IP ultra 7100i │ MIC IP starlight 7100i camera's web page ?
Collection of FAQs for the Video IT Products DIP 6000 & 7000 R2, DIVAR IP AIO 5000/ 7000, DIVAR IP all-in-one 7000 (gen 3), DSA E2700 (EOL), DSA E2800, HP Workstations, HPE Servers
In Bosch VMS it is possible to assign an LDAP user group to a Bosch VMS user group. This article describes why it is important to not assign the same LDAP user group to multiple Bosch VMS user groups.
Username Administrator is not available from the drop-down list, and any generated backdoor password will not work & only one user (other than Administrator) is available in the drop-down list
