Security: Video

This script will make your encoder to toggle relay 1 only when IVA rule #1 alarm is active.

Load balancing is provided with respect to the bandwidth and the number of iSCSI connections and is configurable per IP address (iSCSI target).

Our portfolio contains quite a variety of (mobile) video clients and applications. To get a fast first overview we created the attached table to compare the most important ones.

Operator Client helps you display the original full image circle of a panoramic camera, its image dewarped or you can select a point of interest of the image.

Video Recording Manger v4.00.0070 does not allow anyone not configured in VRM, only as an admin (using Configuration Manager), to log into the VRM Monitor page.

Bosch will undertake a cybersecurity best practice by disabling certain ports on the camera by default. This best practice is being undertaken to reduce potential attack surfaces and limit the exposure of sensitive services, as mentioned in our Data Security Guidebook since years.

To access the "Reset" options of a DIVAR IP 2000 Recording Appliance, you have to open the Appliance's "Dashboard".

  Important note Currently, the VRM is itself very seldom used in combination with Genetec. Starting with 2022, Genetec developed a new driver for Bosch cameras “Hybrid driver for CPP13/14+”. With this, the VRM is not considered anymore. With the old “Legacy (CPP7.3 and older) the VRM is still supported.      Related Products: VRM, Genetec Security Center Overview: It is possible to use VRM free of charge (no extra VRM license is required) within Genetec Security Center. Genetec is sending encrypted secret to the VRM server with the number of the licensed channels. When VRM receives and validates this, it can be used for that number of channels for 24 h. A periodic license update is send by Genetec, so the VRM licensing is guaranteed as long as it is used with Genetec Security Center. Default settings, if not extra configuration is needed or done. -License for 1000 Cameras - License update is done every hour   How to license more than 1000 cameras or change the license update period for VRM within Genetec Security Center: Open the Config Tool and Launch a Video Task Select the Archiver Go to the Resource Tab and click on Extensions From the Tab Installed extensions select Bosch. In the Tab VRM add a new VRM and/or select already configured VRM. Click on Advanced settings and add the following parameters If you need to license the system with more than the default 1000 licenses – create the parameter with Name VrmLicenseRequestCount and as value put the required number of licenses. The parameter name is case sensitive If you need to change the duration of the period between each license request (there is always one license request when the archiver starts) – create the parameter with Name VrmLicenseRequestPeriod. The duration of the period is in milliseconds. The default value is one hour. If the value is set to 0, the license request are disabled. The parameter name is case sensitive     Press Enter to confirm the entry and then Close Press Apply and then OK. At the webpage of the VRM one can check if the number of licenses is changed. If you would like to know how to replay the recordings from a Bosch camera managed by Bosch Video Recording Manager (VRM) in Genetec Security Center software, please follow this video: How to use VRM recording in Genetec Security Center   Note:  To support customer needs and to leverage the most important features of Bosch cameras (like data security, Video Analytics, and intelligent bitrate management), the agreed focus of Bosch and Genetec is on the Genetec Archiver Recording Solution. Current and future developments are focused on this recording solution and the VRM in Genetec will only be supported to maintain existing and upcoming projects where a VRM solution is selected. There will be no development of new features. In this maintenance mode, the following is possible: • Certification of new VRM versions (for projects)* • Certification of new DIVAR IP’s* *Requirement: stable API on VRM side Note: The VRM itself might offer more functionality not covered with the integration in Genetec.

The System Info File is requested during the BVMS license activation via Remote Portal and can be downloaded by following the steps described in this article

This article explains how to set an Unconfigured Bad Drive to Unconfigured Good on a DIVAR IP 6000/ 7000. This step is required if the new drive is not listed under Unconfigured Drives. A possible reason for the Unconfigured Bad status is when a device that has not been removed properly is reconnected to the controller.

Find out from this article in which situations the MAC address cannot be found or only part of the address is correctly extracted in Project Assistant when scanning a QR or Data Matrix code

The default Community Strings for Bosch cameras is - public. To change it, please follow the steps below.

This article contains the step-by-step guide related to the MP4 Video Export from Video Security Client to your PC (Windows) in a local directory. In this article, the Video Security Client is connected to the Remote Portal and explains how you can export video from cameras connected to your RP account.

Video Security Client is the market’s easy to use video surveillance application provided by Bosch for local and remote monitoring of IP cameras and appliances. The software supports small systems from 1 to 128 sites with up to 256 cameras each. Also, you can use Video Security Client being connected to your Remote Portal account. Follow this article and find out the limitations and how can you connect your Remote Portal account to Video Security Client.

Here we describe the steps that would be need to be done to successfully move VRM to a new server.

This article describes the easiest method for adding Expansion shelves to a Base unit DSA E-Series E2600, E2700 or E2800.   This article also applies when: The amount of storage is overloaded and you need additional storage after fully populating the base shelf.   Article requirements: 1. Configuration Manager 2. Configuration Client which is included with BVMS 3. Santricity Software   Step-by-step guide      

What happens when you upgrade the SW of your Management Server form e.g. BVMS 10.0 to BVMS 10.1 and you have not prepared a BVMS 10.1 activation key beforehand?

According to its Data Sheet, the Flexidome IP 3000i IR camera has 2 options to activate the alarm input. Please refer to the diagram from this article if you would like to get alarm input from some physical sensors.

This document is specifically for DIP-73xx as it's the only DIP with Software Center. The document details how to upgrade all the way from BVMS 10.1 with Software Center and to BVMS 12.1/ 12.2 with System Manager 2.3 

Please keep in mind that for SNMP v3 only the the Standard MIB II file is supported. This means that only general network device performance monitoring parameters can be requested. There is no Bosch Private MIB II extension for SNMP v3.