Security: Video

Bosch Remote Portal provides the VideoView+ Service which allows to display live video, replay of recorded video on the camera, and a forensic search on Video Security Client. Further the Video Security App (on iOS and Android) can receive push alarm notifications triggered by motion in the camera image, for example. This article explains how to configure this service to receive push alarm notifications.

This article explains what is the Intelligent Dynamic Noise Reduction (iDNR) in Bosch cameras.

This article explains what is the difference between video coding H264 and H265 (Bosch cameras).

The following instruction describes how to configure a data partition from RAID 5 to RAID 6 on the DIVAR IP all-in-one 7000 4th generation. It is not possible to directly migrate from RAID 5 to RAID 6, so the first step is to delete RAID 5 and then create RAID 6.

This article explains if is it possible to enable Remote Desktop on DIVAR IP all-in-one 6000 and connect on it remotely.

This article explains why the Live view shows ‘Authentication failed’ in Video Security App.

When doing a pull point subscription, at the Start of the events Rule Engine/LineDetector/Crossed is missing, even though the rule is configured, and is given in the GetEventProperties response. The topic name space for RuleEngine/ FieldDetector/ ObjectInside works as expected.

In order to determine the Time Zone values, perform the bit mask operation of the flag value with the combined bit mask value 0x1F800000 as shown below. Bits 23-28 correspond to the Time Zone bits in the Flags.

Limited user is available on DIVAR IP all-in-one 4000, if the unit has HDDs inside. Every setup with DIVAR IP System Manager, on any DIP (AIO 7000 GEN 3, AIO 4000, AIO 5000, AIO 6000) that is "00N" (without HDDs) will fail and result in a lack of a "limited user" and "kiosk mode", if you do not insert the HDDs and perform the necessary steps from the manual.

Find out from this article how to configure a singe mode VIF on NetApp array. For example if we have 2 (or more) physical interfaces, how to connect them to different network segments and, if one of the segments fails, the second network interface to step in automatically?

This will let you call up cameras on an Allegiant monitor output across the network to a remote site.

The thermal mode is saved in the preposition settings. If you have changed the thermal mode of the camera in the Picture Settings Thermal page and you also want the Thermal color mode to apply to the existing saved pre-position, you have to re-save the pre-position again.  

Aside from configuring the camera using its own browser, there are other tools you can use to setup the camera. The choice when using which tool will come down to the individual installer. Their experience and know-how of the tool will dictate which one they will use. 

What FW versions did Crowd Density Estimation get removed from IVA Pro? What to use in replacement for Crowd Density Estimation? How to remove the unrecognized task?

By default, the DIVAR IP all-in-one 7000 devices are intended to operate with one or two local monitors, connected to HDMI interfaces on the rear of the unit. If NO HDMI is connected, then iKVM over BMC port is active and available. In this case, it is supported to remove VGA cover and use it as local admin monitor, not to run the Operator Client.

The Table view provides the option of presenting a summary of specific settings for individually selected devices in the form of a clearly arranged  table.  The content of all main tabs and sub-tabs can be exported in *.csv format.

Bosch's Remote System Management service allows you to leverage the power of the Internet of Things (IoT) to provide secure, transparent, and cost-effective asset management throughout the lifecycle of a video system. This service enables end users, system integrators and installers to perform inventory and update management, as well as health monitoring tasks for an entire Bosch video system (DIVAR IP + BVMS + cameras) from one centralized Remote Portal platform.

This article describes the method about how you can import a .txt file containing a group of cameras from Configuration Manager in Project Assistant App.

In order to add the Subject Alternative Name, you can use "Bosch Configuration Manager" or the camera's web page using latest Firmware

Bosch recommends that the operating systems used by the video surveillance system are constantly updated, with a maximum update cycle of 6 months. Windows updates often include fixes for recently discovered security vulnerabilities, such as the Heartbleed SSL vulnerability, which affected millions of computers worldwide.