Security: Video

This article explains if is it possible to enable Remote Desktop on DIVAR IP all-in-one 6000 and connect on it remotely.

Limited user is available on DIVAR IP all-in-one 4000, if the unit has HDDs inside. Every setup with DIVAR IP System Manager, on any DIP (AIO 7000 GEN 3, AIO 4000, AIO 5000, AIO 6000) that is "00N" (without HDDs) will fail and result in a lack of a "limited user" and "kiosk mode", if you do not insert the HDDs and perform the necessary steps from the manual.

The following instruction describes how to configure a data partition from RAID 5 to RAID 6 on the DIVAR IP all-in-one 7000 4th generation. It is not possible to directly migrate from RAID 5 to RAID 6, so the first step is to delete RAID 5 and then create RAID 6.

By default, the DIVAR IP all-in-one 7000 devices are intended to operate with one or two local monitors, connected to HDMI interfaces on the rear of the unit. If NO HDMI is connected, then iKVM over BMC port is active and available. In this case, it is supported to remove VGA cover and use it as local admin monitor, not to run the Operator Client.

This article explains which is the difference between BVRAdmin lost password versus VRM lost password (reset) of DIVAR IP.

This article provides you with information related to the Windows Firewall, how to access, configure and adjust it.

Bosch has been providing 2 types of VRM packages: a 32bit and a 64bit version. Since VRM 3.82 we are only offering the 64bit version.  

According to the DIP Whitepaper, the unit supported 128 channels before upgrading. After upgrade to BVMS >= 11.0, having the MBV-BPLU-DIP base, the channels licenses limit is 256 channels 

The following instruction describes how to configure the data disk in a RAID1 configuration on the DIVAR IP all-in-one 4000. Is important to keep in mind that the configuration of the data disks in RAID1 will cause DATA LOSS on the disks used to create the RAID configuration

This article is a step-by-step guide about how to update the BIOS on the DIVAR IP all-in-one 7000 4th gen (DIP-74xx).

This article shows where to find the BIOS default password of DIVAR IP all-in-one 7000 gen4 (DIP-74xx).

The ASUS Inband Tool is the preferred log collection tool, all relevant logs can be gathered from there for ASUS Tech Support. LSI Storage Authority, LSA for short, can be found on the DIP74xx’s Windows desktop. 

With the release of the DIVAR IP all-in-one 7000 gen4 (DIP-74xx), a new tool is available for health monitoring and log gathering, it essentially replaces SuperMicro’s SuperDoctor5; the ASUS Inband Tool. This tool operates as a service on the DIP and provides a webpage with hardware health monitoring options, hardware status details, and hardware information, as well as an option to export logs and run reports.

Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading.

The BVRAdmin password is a password for a Windows user and needs to be changed accordingly, from Windows settings. Please be aware that if you have BVMS installed on your DIVAR, it is important to change in BVMS Configuration Client the iSCSI target password after this was changed for BVRAdmin user.

Yes. Since the system does not have a valid SMA, the Central Technical Support team cannot perform the license transfer from one unit to the other.

This troubleshooting guide, will guide you through the recovery steps of a DIVAR IP 6000 or 7000, DIVAR IP 6000 R2 or 7000 R2, without video data loss

This document is specifically for DIP-71xx as it's the DIP which supports certain versions of BVMS (regular BVMS installer) and must be updated in a certain order. The document details how to upgrade from BVMS v8 to BVMS v12.0.1.

Regular BVMS 12.1 installer will not run on any DIVAR IP all-in-one platform. The upgrade shall be performed via DIVAR IP System Manager application.

Regular BVMS 12.1 installer will not run on any DIVAR IP all-in-one platform. The upgrade shall be performed via DIVAR IP System Manager application. Usually, we recommend to upgrade BVMS in steps. Each version should not be more than ~two years apart. This prevents potential issues in the upgrade process.