Security: Video

Answer It only depends on the version of BVMS you have. If you have BVMS 7.5, certain cameras with a certain FW have been tested and are supported. If you have BVMS 8.0, certain cameras with a certain FW have been tested and are supported. For BVMS versions of 9.0 or lower, only tested cameras must be added, otherwise we cannot support new setup. On DIP 3000 you can only upgrade to BVMS 8.0. The version of Windows installed on it does not support older versions of BVMS, it is not compatible. Recommended to use BVMS 8.0, the largest version supported on that unit. You need to make sure that those cameras are on the list of tested devices of the version you have.   Regarding the ONVIF Compatibility of the cameras, please see the following Bosch Knowledge Base article: https://community.boschsecurity.com/t5/Security-Video/BVMS-ONVIF-Device-compatibility/ta-p/4252

The Intelligent Insights widgets can be visualized in BVMS Operator Client. In this article we are going to show you how to add a widget to Bosch Video Management System (BVMS).

Central Support Team may ask you to provide them with the log files and configuration file of Intelligent Insights.This article explains you how and where you can get them.

The following procedure describes how to restore DIVAR IP 5000 ALL-IN-ONE to the factory default image.   Step-by-step guide   1. Start the unit and press F7 during the BIOS power-on-selftest. The Recovery menu is displayed.   2. Select one of the following: – Initial factory setup: restores to factory default image and deletes all data on the HDDs. or – System Recovery (back to Factory Defaults): restores to factory default image; data on the HDDs will not be deleted.   Note: While the System Recovery option doesn't delete video footage stored on the data HDDs, it still replaces the complete OS (operating system) partition (including VMS settings) with a default configuration. In order to access existing video footage after recovery, the VMS configuration needs to be exported before System Recovery and re-imported afterwards.   Notice! Do not turn off the unit during the process. This will damage the Recovery media.   3. The unit starts from the Recovery media. If the setup is successful, press OK to restart the system.   4. Windows performs the initial setup of the operating system. The unit restarts after Windows has completed the setup. 5. After the restart of the unit, the factory settings are installed. 6. After the system has reboot, the next step is to change the BVRAdmin password. The default one is WSS4Bosch.

Follow the steps from this article when an error message appears on your DIVAR IP 5000 AIO during license activation process

  What does mean the clock symbol showed in the Operator Client Logical tree?

When camera is set to auto track (by web interface) to "auto"-> IVA is detecting an object but camera is not following. Auto tracking works and metadata is displayed only on a stored preposition.

Find out from this article how to pass a special connection string to request a multicast stream via RTSP from a BOSCH IP camera or IP encoder.

Check this article and find out what you can do if you are using one Divar network 2000 and you have a new Flexidome IP 5000i IR camera, but you cannot add it to the Divar because it is not displayed in “Detection” > “Device search” screen.

This article explains how to integrate the Bosch MIC IP 7000 HD camera series into any existing analog CCTV system using the Bosch VIDEOJET decoder 3000. The most common integration scenarios are listed below: Simple integration using direct connectivity to analog monitor and joystick, typically found in single camera installation (for example, mobile surveillance vehicles) Integration into an existing analog matrix switcher typically found in large installations (such as for city surveillance)

The Smart Notification service lets your end-customer easily keep track of business operations. Detection, notification and storage of events like warehouse access, POS transactions or goods delivery enable efficient monitoring and resolution of critical events for the business owner. Please follow below steps to set up a Smart Notification service.

Answer This guide is meant to explain how you can find the connection state events of a camera in Operator Client - Bosch Video Management System.

If you suspect that your hard drive has failed and you are contacting the Central Technical Support team, please first consider the mandatory information listed below, which must be provided to them.

In terms of license activation process and compared to other versions of BVMS (<v11.0), the Bosch Remote Portal replaces the Bosch Software License Manager System (SLMS), starting with BVMS v11.0.

In this section you can find details on what information is required during the troubleshooting process to successfully identify a unit in terms of model number, firmware version and unique identifiers. What is also very important always for the troubleshooting is the DIVAR Service log. In addition to that, in some situations network captures from the DIVAR may also be required.  

An object moving or a low/ higher contrast scene can throw off the autofocus option, resulting in a soft focus or even not focus at all. Using manual focus is an obvious solution, but manual focus isn’t exactly easy to get sharp images. Manual focus requires a bit of know-how and some practice to get right. If you would like to improve the performance and get a sharp image, please see below how you can manually adjust the focus ring on a Dinion Thermal camera.

Follow this article to avoid getting the message: “Changing orientation is not possible because of the mounted illuminators”.

If your DINION IP Thermal 8000 (NHT-8000) camera is reporting blurred/unclear/unsharp images that are randomly appearing during the day, or the night, please follow the steps below in order to fix it.

Sometimes it is preferable to have a different “user mode” during the day then in the night. Our cameras by default have the option to switch the user mode e.g. triggered by the camera D/N switch over. But also other triggers can be chosen. Below an example how to setup the “user mode” switching triggered by the D/N switch over.

Some options have been removed when compared to previous CPPs, as they are only useful for moving cameras. Find here the overview of the web page of ‘Live’ functions section and the options remained available for FLEXIDOME multi 7000i (CPP14) cameras.