Security: Video

BVMS v10.1 and  BVMS v11.0 come with a checkbox where you can logon to the Operator Client with Windows Credentials. If you want to use this function, you need to set up the BVMS Configuration Client and browse the AD users-groups. Then, the users can sign in to Operator Client with their Windows-Credentials. 

Before using the App please make sure that you have configured the Passwords, users and ports on your DIVAR and the same data is entered in the App.

Configuration Manager 7.60 by default will only trust CA signed certificates. Changing the security requirements will change the behavior of how CM displays the connection/access.

Have a look at this article and learn how to fix the Add Scriptlet button which does not become active. It stays grayed out. Same happens with ClientScript and ServerScript.

If you want to be able to replay the recording for the complete retention time, you should use VRM replay. VRM should be accessible and added to the VSC

"Show VCA items" is a function which works in Internet Explorer 11 with the Bosch MPEG ActiveX installed. Due the end-of-life of Internet Explorer, this function is no longer available on Microsoft Edge.

Upon powering on the DIVAR IP all-in-one 7000 system you hear FAN spinning normal, LEDs are blinking at normal frequency and there are no error beep codes. However, there is no display when connected via VGA (or) DVI (or) DP. Check out this article and find out how to fix this!

This article shows how to configure Input Alarm and later search for them in the Event search using Web Interface.

This article describes all the steps that will help you to create iSCSI Virtual Disk/LUNs after replacing an HDD on a DIVAR IP 5000 AIO.

There are two methods of working with 3rd party apps: through Remote Portal and Configuration Manager. In this article you will find the step-by-step guide where is described the method using Configuration Manager.

Monitor Group gives operators flexible control over the content of a video wall or allows them to let the system take over this control automatically based on pre-defined scenarios. This article describes how to create a Monitor Group on a decoder VJD 7xxx/ 8xxx in BVMS Configuration Client

Can I mask areas that should not trigger an alarm (e.g. false detection due to sun reflection)?

At startup, a black screen is showing up and it is impossible to boot into the BIOS or attempt a reset by pressing the F7 key. How to fix this?

The latest suitable Image for your DIVAR IP R2 Family Device can be obtained from Bosch Central Support Team. Please provide the SN (serial number) from the DIVAR IP 6000/7000 R2 when contacting Bosch Central Support Team.

This article contains all the steps to restore DIVAR IP 7000 R2 to factory default. Note: By performing the Initial Factory Setup on the system, ALL DATA from the ENTIRE system will be erased.

If you are interested in retrieving the stream of an IP camera using multicast, please check out the options from this article.

Are you looking for the MIC IP fusion 9000i Wiper/Washer RCP command syntax to incorporate it in the third party software?

From this article you will find out how to set up the IP Matrix configuration on the VIDEOJET decoder 7000 (VJD-7513) using Configuration Manager.   The built-in IP Matrix functionality, together with a connected keyboard, allows VIDEOJET decoder 7000 to run as a stand-alone system. An operator can manage up to 32 cameras via the keyboard without any PC or management system required. System setup is quickly done with Configuration Manager. After that, no PC is required to run the IP Matrix   Note: According to the Release letter (Firmware 9.51) of VJD-7513, VIDEOJET decoder 7000 supports IP Matrix application as built-in feature. According to the Release letter (Firmware 54.8.02) of VJD-7000, IP matrix remote monitor is only possible with UDP. TCP not supported. ** VJD-7000 can be used as an extended monitor to IP Matrix in single and quad view. Please check also the following article and find out: Which are the system requirements for configuration/ operation of VIDEOJET decoder 3000/ 7000/ 8000?   A single system can support: 2 physical monitor displays One KBD-Universal XF keyboard 32 cameras 32 camera sequences 9 favorite views

MQTT is a Client Server publish/subscribe messaging transport protocol.

The unit can receive the time signal from a time server using various time server protocols and then use it to set the internal clock. The device polls the time signal automatically once every minute. To check the NTP connection from the camera please follow this article.