Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎05-03-2022 11:35 AM
    This article shows how to check if particular non Bosch camera is supported in BVMS.
    View full article
    ‎03-18-2022 03:13 PM
    This article describes how to use Milestone's PTZ  "Home" position with Bosch PTZ cameras.
    View full article
    ‎02-20-2023 03:38 PM
    This article contains videos which explain the usage of Bosch cameras integrated in Genetec Security Center.
    View full article
    ‎02-21-2023 10:03 AM
    Let’s suppose that you have one setup which consists in an Adam 6060 I/O module, BVMS and a DINION IP thermal 8000 camera. Can the state of an ADAM relay module be changed when the IVA from the camera generates an alarm?
    View full article
    ‎06-26-2024 08:45 AM
    To ensure the highest customer satisfaction and replace the defective hardware faster and more smoothly, it is necessary to register each system for the specific country together with the system location. But where and why should you register your device?
    View full article
    ‎05-03-2022 11:41 AM
    This article lists the initial troubleshooting steps for issues with ONVIF cameras, added to BVMS system as Live Only ONVIF cameras. The specific point in this scenario is VSG is not used.  
    View full article
    ‎05-05-2023 08:32 AM
    Using the following command you can reset the result of People counting via SDK: http://<IP_address>/rcp.xml?command=0x0b4a&type=P_OCTET&direction=WRITE&num=1
    View full article
    ‎03-18-2022 03:36 PM
    The article describes how to receive analytic events from Bosch cameras in Milestone XProtect.
    View full article
    ‎03-18-2022 03:58 PM
    This article explains what to do when a device scan from within Milestone XProtect is not exposing all Bosch cameras in the network.
    View full article
    ‎03-18-2022 03:49 PM
    XProtect offers 3 different modes of metadata streaming. What are the differences there?
    View full article
    ‎03-18-2022 03:21 PM
    This article describes how to secure the data connection between Bosch cameras and Milestone's XProtect by the use of 'Authority-signed Certificates' 
    View full article
    ‎02-09-2023 10:55 AM
    In some cases the IVA tasks can get lost after firmware update, but you can avoid this by copying the IVA configuration. There are 2 ways. In both ways it's not guaranteed that all task shall work afterwards since new firmware version can contain a new IVA version with new features.
    View full article
    ‎06-19-2023 01:18 PM
    This article explains what to do with missing metadata in Milestone XProtect.
    View full article
    ‎04-27-2023 12:45 PM
    For all ONVIF, RTSP and JPEG cameras we only support one live stream, and for ONVIF you can only select which profile to use for this one live stream. 
    View full article
    ‎10-18-2023 04:16 PM
    Check this article and find the compatibility matrix between Bosch cameras and Milestone
    View full article
    ‎09-08-2023 09:33 AM
    This article describes how to change the communication ports that are used by the Bosch Forensic Search inside a Genetec installation. The default communication port between the Bosch server components is 5051. It may happen that this port is already in use by another process and hence the setting needs to be changed. Such a situation would be exposed to the user as a 'Server error' when trying to execute a search and a log entry would be created, indicating the the FSS validation is not possible.
    View full article
    100% helpful (1/1)
    ‎01-12-2024 09:46 AM
    During the troubleshooting process, the Central Technical Support team often needs to run several different loggers to gain a more complete understanding of the problem. This log collection method is useful only when an issue can be reproduced fast, because the logs are overwirtten.
    View full article
    ‎06-20-2023 04:03 PM
    The available cameras in the configuration dialog is controlled by 2 criteria: The camera needs to be a Bosch camera AND the camera needs to have some metadata recording available in XProtect
    View full article
    ‎07-02-2024 09:43 AM
    This article outlines the required license for operating a Bosch Forensic Search within the Genetec Security Center.
    View full article
    ‎01-09-2024 08:46 AM
    This article explains how to enable or disable audio recording for specific camera in BVMS, on action of BVMS Operator Client user.   Follow the step-by-step guide from this article.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist