Security: Video

This is how every VRM behaves when it is accessed in a web Browser. This is happening because there is no https certificate loaded on the VRM and you can't even create a self-signed certificate for HTTPS access like for cameras. You need to click on "Advanced" and then on the link bellow. So, this is the way it is intended to work.

Video Recording Manger v4.00.0070 does not allow anyone not configured in VRM, only as an admin (using Configuration Manager), to log into the VRM Monitor page.

This article describes how to set LUNs on a target to Read Only via Configuration Manager.

The default behavior of VRM is to redirect requests from "HTTP" to "HTTPS" via the HSTS setting. Never change VRM or any device settings via CM if they are managed by BVMS - BVMS will revert the settings back to previous state as set in BVMS Cc

At some point of the troubleshooting process, the customers might be asked to force the VRM to do a full initial discovery.

For VRM (Video Recording Manager) stand-alone Systems and Servers with VSG (Video Streaming Gateway) installed, it is strongly recommended to check for Microsoft OS updates before the VRM Master Installer is installed/updated.

An installer doesn’t need to travel to customer's site for fine tuning the configuration, when a Camera Analytics task brings false alarms. The VCA task editor can be used for easy analytic configuration or for troubleshooting.

This article explains if you can receive / retrieve more than 4 live video streams with BOSCH Video Security Client on Windows PC

Starting with BVMS v10.0, you can leverage VRM Encryption Technology.

Glutton (German: Vielfraß) defines and prevents a camera or multi-channel encoder from mounting and consuming  a large number of  blocks in a very short time.

If replacing a defective camera, the camera must be the same IP address as the defective device, and it cannot contain a GUID from a different VRM.

Find out from this article if there are restrictions of VRM Configuration utility pre-installed on DLA

This article presents possible causes and solution regarding no recording for cameras added to VRM (DIP 7000AIO): ‘Unexpected error’ in BVMS Config Client

Check if your system is performing correctly! The VRM Monitor is one of the best options to check if the system is recording correctly, providing a quick overview as well as detailed information about all the cameras and storage added to VRM. In this article you are going to see how to access VRM Monitor from Bosch Video Management System (BVMS) Configuration Client. Furthermore, you will find here some useful information about each section on the Dashboard page.

  Important note Currently, the VRM is itself very seldom used in combination with Genetec. Starting with 2022, Genetec developed a new driver for Bosch cameras “Hybrid driver for CPP13/14+”. With this, the VRM is not considered anymore. With the old “Legacy (CPP7.3 and older) the VRM is still supported.      Related Products: VRM, Genetec Security Center Overview: It is possible to use VRM free of charge (no extra VRM license is required) within Genetec Security Center. Genetec is sending encrypted secret to the VRM server with the number of the licensed channels. When VRM receives and validates this, it can be used for that number of channels for 24 h. A periodic license update is send by Genetec, so the VRM licensing is guaranteed as long as it is used with Genetec Security Center. Default settings, if not extra configuration is needed or done. -License for 1000 Cameras - License update is done every hour   How to license more than 1000 cameras or change the license update period for VRM within Genetec Security Center: Open the Config Tool and Launch a Video Task Select the Archiver Go to the Resource Tab and click on Extensions From the Tab Installed extensions select Bosch. In the Tab VRM add a new VRM and/or select already configured VRM. Click on Advanced settings and add the following parameters If you need to license the system with more than the default 1000 licenses – create the parameter with Name VrmLicenseRequestCount and as value put the required number of licenses. The parameter name is case sensitive If you need to change the duration of the period between each license request (there is always one license request when the archiver starts) – create the parameter with Name VrmLicenseRequestPeriod. The duration of the period is in milliseconds. The default value is one hour. If the value is set to 0, the license request are disabled. The parameter name is case sensitive     Press Enter to confirm the entry and then Close Press Apply and then OK. At the webpage of the VRM one can check if the number of licenses is changed. If you would like to know how to replay the recordings from a Bosch camera managed by Bosch Video Recording Manager (VRM) in Genetec Security Center software, please follow this video: How to use VRM recording in Genetec Security Center   Note:  To support customer needs and to leverage the most important features of Bosch cameras (like data security, Video Analytics, and intelligent bitrate management), the agreed focus of Bosch and Genetec is on the Genetec Archiver Recording Solution. Current and future developments are focused on this recording solution and the VRM in Genetec will only be supported to maintain existing and upcoming projects where a VRM solution is selected. There will be no development of new features. In this maintenance mode, the following is possible: • Certification of new VRM versions (for projects)* • Certification of new DIVAR IP’s* *Requirement: stable API on VRM side Note: The VRM itself might offer more functionality not covered with the integration in Genetec.

This article explains how you can collect VRM logs in different versions of it

This article presents where are the Transcoder Log settings and how to enable them for log collection.  

This article is a step-by-step guide about how to disable the Live and Playback page in VRM monitor version higher than 4.10.  

In many cases a minimum and maximum retention time needs to be defined in a video surveillance systems due to legal requirements. While the minimum retention time defines the time period for how long video recordings need to be stored, the maximum retention time defines after which period of time the recordings have to be deleted. Thus, the minimum retention time is going to influence the amount of storage needed. The higher the minimum retention time the more storage space is required.

Find out from this article which VRM version is compatible with your DIP and what BVMS version is supported.