Security: Video

Video Recording Manger v4.00.0070 does not allow anyone not configured in VRM, only as an admin (using Configuration Manager), to log into the VRM Monitor page.

  Important note Currently, the VRM is itself very seldom used in combination with Genetec. Starting with 2022, Genetec developed a new driver for Bosch cameras “Hybrid driver for CPP13/14+”. With this, the VRM is not considered anymore. With the old “Legacy (CPP7.3 and older) the VRM is still supported.      Related Products: VRM, Genetec Security Center Overview: It is possible to use VRM free of charge (no extra VRM license is required) within Genetec Security Center. Genetec is sending encrypted secret to the VRM server with the number of the licensed channels. When VRM receives and validates this, it can be used for that number of channels for 24 h. A periodic license update is send by Genetec, so the VRM licensing is guaranteed as long as it is used with Genetec Security Center. Default settings, if not extra configuration is needed or done. -License for 1000 Cameras - License update is done every hour   How to license more than 1000 cameras or change the license update period for VRM within Genetec Security Center: Open the Config Tool and Launch a Video Task Select the Archiver Go to the Resource Tab and click on Extensions From the Tab Installed extensions select Bosch. In the Tab VRM add a new VRM and/or select already configured VRM. Click on Advanced settings and add the following parameters If you need to license the system with more than the default 1000 licenses – create the parameter with Name VrmLicenseRequestCount and as value put the required number of licenses. The parameter name is case sensitive If you need to change the duration of the period between each license request (there is always one license request when the archiver starts) – create the parameter with Name VrmLicenseRequestPeriod. The duration of the period is in milliseconds. The default value is one hour. If the value is set to 0, the license request are disabled. The parameter name is case sensitive     Press Enter to confirm the entry and then Close Press Apply and then OK. At the webpage of the VRM one can check if the number of licenses is changed. If you would like to know how to replay the recordings from a Bosch camera managed by Bosch Video Recording Manager (VRM) in Genetec Security Center software, please follow this video: How to use VRM recording in Genetec Security Center   Note:  To support customer needs and to leverage the most important features of Bosch cameras (like data security, Video Analytics, and intelligent bitrate management), the agreed focus of Bosch and Genetec is on the Genetec Archiver Recording Solution. Current and future developments are focused on this recording solution and the VRM in Genetec will only be supported to maintain existing and upcoming projects where a VRM solution is selected. There will be no development of new features. In this maintenance mode, the following is possible: • Certification of new VRM versions (for projects)* • Certification of new DIVAR IP’s* *Requirement: stable API on VRM side Note: The VRM itself might offer more functionality not covered with the integration in Genetec.

Here we describe the steps that would be need to be done to successfully move VRM to a new server.

If replacing a defective camera, the camera must be the same IP address as the defective device, and it cannot contain a GUID from a different VRM.

This article gives you the solution to fix the behavior when the recording doesn't work for VG4 AutoDome camera and when the Bosch logo is displayed in the cameo

Is DIVAR IP 6000 R1 compatible with VRM v.3.83.0021 (64-bit) and BVMS Viewer 10.1?

Check this article and find out what the Start Manual Recording button of VRM Camera Cameo does in BVMS Operator Client

By design, the Dual-Recording feature is specific only in Bosch Cameras. 3rd party cameras are integrated into Bosch Systems like BVMS-VRM via our Video Streaming Gateway (VSG)

Note that this procedure applies only from VRM version 3.10 onwards.

Find out from this article if there are restrictions of VRM Configuration utility pre-installed on DLA

There is an issue with VRM versions lower than 4.0 where the retention time for recordings from VSG instances is set incorrectly. There are a few things that usually cause the recording mode to be set incorrectly. Find out more details from this article!

This article presents where are the Transcoder Log settings and how to enable them for log collection.  

Starting with BVMS v10.0, you can leverage VRM Encryption Technology.

The default behavior of VRM is to redirect requests from "HTTP" to "HTTPS" via the HSTS setting. Never change VRM or any device settings via CM if they are managed by BVMS - BVMS will revert the settings back to previous state as set in BVMS Cc

At some point of the troubleshooting process, the customers might be asked to force the VRM to do a full initial discovery.

With the new VRM eXport Wizard, we offer the possibility to use CLI commands to do exports without needing to open the application.

This article is a step-by-step guide about how to disable the Live and Playback page in VRM monitor version higher than 4.10.  

Since VRM 4.10, we have reintroduced the Live & Replay pages in the VRM web GUI.

Glutton (German: Vielfraß) defines and prevents a camera or multi-channel encoder from mounting and consuming  a large number of  blocks in a very short time.

An installer doesn’t need to travel to customer's site for fine tuning the configuration, when a Camera Analytics task brings false alarms. The VCA task editor can be used for easy analytic configuration or for troubleshooting.