Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    ‎07-19-2021 11:20 AM
    Sometimes it is preferable to have a different “user mode” during the day then in the night. Our cameras by default have the option to switch the user mode e.g. triggered by the camera D/N switch over. But also other triggers can be chosen. Below an example how to setup the “user mode” switching triggered by the D/N switch over.
    View full article
    ‎06-28-2024 01:46 PM
    According to its Data Sheet, the Flexidome IP 3000i IR camera has 2 options to activate the alarm input. Please refer to the diagram from this article if you would like to get alarm input from some physical sensors.
    View full article
    ‎08-29-2023 10:48 AM
    DIVAR IP units can be upgraded to BVMS 11.0. Starting with BVMS 11.0, the BVMS licensing scheme also applies to the DIVAR IP units. This document describes which units you can upgrade to BVMS 11.0 and which licenses you have to order for a DIVAR IP unit!
    View full article
    ‎06-08-2023 09:05 AM
    A password prevents unauthorized access to the device. You can use different authorization levels to limit access. Proper password protection is only guaranteed when all higher authorization levels are also protected with a password. Therefore, you must always start from the highest authorization level when assigning passwords. This article will guide you step by step to set the destination password for decoders.
    View full article
    ‎07-25-2024 01:37 PM
    Do not upgrade the camera FW directly to 7.81. Otherwise, “error 13: device check failed” message will be displayed, and the FW will not be upgraded successfully.
    View full article
    ‎08-29-2023 10:31 AM
    Intelligent Insights is a standalone product. The system can run as a standalone system and be accessed by operators via the web browser or the widgets can be integrated in a BVMS operator client.
    View full article
    ‎03-14-2023 10:28 AM
    There are two methods of working with 3rd party apps: through Remote Portal and Configuration Manager. In this article you will find the step-by-step guide where is described the method using Configuration Manager.
    View full article
    ‎11-29-2022 04:09 PM
    The purpose of this article is to help you disabling the compass character from the Screen Display (OSD) of the Bosch PTZ camera via its web interface
    View full article
    ‎02-09-2023 10:55 AM
    In some cases the IVA tasks can get lost after firmware update, but you can avoid this by copying the IVA configuration. There are 2 ways. In both ways it's not guaranteed that all task shall work afterwards since new firmware version can contain a new IVA version with new features.
    View full article
    ‎05-31-2024 03:37 PM
    You can collect Service logs from the unit using two methods. Both methods will save the service logs as a password protected ZIP file ( Example: ServiceLog-XXXXX.zip ).
    View full article
    ‎08-04-2022 08:15 AM
    The default SMTP port number for Bosch IP cameras is 25. The required SMTP port can differ depending on the service provider. From FW 5.80.0073 onwards it is possible to change the SMTP port using Alarm Task Script Language (ATSL).
    View full article
    ‎11-21-2022 01:41 PM
    Before you can operate your VIDEOJET decoder 7000/ 8000 within your network, it must have a valid IP address for your network and a compatible subnet mask. This articles explains how you can change the IP Address of VIDEOJET decoder 7000/ 8000 using Configuration Manager.
    View full article
    ‎05-31-2024 03:46 PM
    This article explains you how and where you can get the logs of your camera. The system logs are extremely useful for troubleshooting recurring or obscure problems, as they provide a record of all work performed on the system and may shed light on hard-to-spot interactions between seemingly unrelated symptoms.  
    View full article
    ‎03-03-2023 11:48 AM
    From this article you will find out how to set up the IP Matrix configuration on the VIDEOJET decoder 7000 (VJD-7513) using Configuration Manager.   The built-in IP Matrix functionality, together with a connected keyboard, allows VIDEOJET decoder 7000 to run as a stand-alone system. An operator can manage up to 32 cameras via the keyboard without any PC or management system required. System setup is quickly done with Configuration Manager. After that, no PC is required to run the IP Matrix   Note: According to the Release letter (Firmware 9.51) of VJD-7513, VIDEOJET decoder 7000 supports IP Matrix application as built-in feature. According to the Release letter (Firmware 54.8.02) of VJD-7000, IP matrix remote monitor is only possible with UDP. TCP not supported. ** VJD-7000 can be used as an extended monitor to IP Matrix in single and quad view. Please check also the following article and find out: Which are the system requirements for configuration/ operation of VIDEOJET decoder 3000/ 7000/ 8000?   A single system can support: 2 physical monitor displays One KBD-Universal XF keyboard 32 cameras 32 camera sequences 9 favorite views
    View full article
    ‎06-10-2021 09:43 AM
    Perhaps you are wondering how to set the maximum retention time on a Divar Network? Some of our customers asked about this option. Well, in DIVAR Network and Hybrid there is not retention time. But you can set the automatically deleting time, that is more or less the same.   Step-by-step guide:   Open one Browser and type your device IP address Login with the administrator account Go to Settings > Storage > Recording Fill in the box with the desired automatic deletion time   Another option is to make this change directly in the local interface of the unit.
    View full article
    ‎06-10-2021 09:32 AM
    Short intro and related topics: This article will review the settings required to configure Windows as a NTP time server. Note: If you are running VRM and have the Time Server enabled, you must disable the Time Server before performing the following. Article requirements: Windows Server 2016/ Windows 10
    View full article
    ‎06-10-2021 09:14 AM
    Find below Gmail SMTP settings which you have to set in your EMAIL screen of DIVAR Menu. SMTP Server address: smtp.gmail.com Username: Your Gmail e-mail adress Password: Your Gmail password Port (TLS😞 587 Port (SSL😞 465 TLS / SSL required: Yes TLS : Transport Layer Security         SSL: Secure Sockets Layer What happens if you do not select either one? If neither SSL nor TLS is used , then the communication line can easily become a party line for eavesdroppers, all data transmitted between DIVAR and e-mail account for anyone to see.
    View full article
    ‎02-21-2023 10:53 AM
    It is possible to add ONVIF compliant cameras to Bosch Video Management System as live only devices or as VSG devices (then the cameras will also record). This article explains how to add an ONVIF camera as VSG device in full Bosch Video Management System (BVMS 10.1). We recommend using Bosch Workstations and Servers. They are fully tested and optimized for Bosch Video Management System.   Article requirements: BVMS installed ONVIF camera. Please refer to BVMS - ONVIF Device compatibility for additional information. PC/ Server/ Workstation
    View full article
    ‎01-12-2023 04:55 PM
    This article explains how to connect an INTEOX camera to the S&ST ecosystem using Configuration Manager (7.20 and later).
    View full article
    ‎05-25-2021 10:11 AM
    In Cloud-based Services, different 'Actions' can be configured for automatic processing as well as manual action for the operators (Alarm Agents). There are 2 different options how an action is processed: An 'Automatic Action' is processed automatically when the related Service Scenario is performed. An 'Intervention Action' is executed manually by an operator from the Cloud-based Service Operator Interface. This note shows available actions in Cloud-based Services and provides a step by step instruction to configure these actions.   Step-by-step guide   1. Send e-mail "Send e-mail" sends an e-mail notification to the configured recipient(s). The action can be used as manual action for the operators (Intervention Action). The content of the alarm email can be configured to the customer's needs.   To configure a "Send e-mail" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Email'. 6. Type recipients, CC's, mail subject and message. Use the pull down to enter environment variables to the e-mail text. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   2. Execute PTZ Command "Execute PTZ Command" starts an auxiliary command on a Pan-Tilt-Zoom (PTZ) camera. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Note the available auxiliary commands in the camera’s manual. To configure an "Execute PTZ Command" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Execute PTZ Command'. 6. Select PTZ camera, select auxiliary command and type the command No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing   3. Go to PTZ Preposition "Go to PTZ Preposition" moves a Pan-Tilt-Zoom (PTZ) camera to a preposition. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). The prepositions (shots) need to be configured via the Device Page upfront. To configure a "Go to PTZ Preposition" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Go to PTZ preposition'. 6. Select PTZ camera and type the preposition No. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   4. Play Audio on Device "Play Audio on Device" replays an audio file directly from the device's loudspeaker. The action is intended to perform standard audio interventions without the need for the operator (alarm agent) to talk. "Play Audio on Device" can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). Audio files need to be prepared and installed by CBS development. If you want to use your own audio files, please get in contact with technical support. To configure a "Play Audio on Device" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account. 3. Click tab 'Actions'. 4. Click '+' button to add an Action. 5. Give the Action a descriptive name and select 'Play audio on device'. 6. Select the audio device and select the audio file. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   5. Switch Relay "Switch Relay" switches a relay of one or more IP devices. The action can be used for automatic processing (Automatic Action) as well as manual action for the operators (Intervention Action). To configure a "Switch Relay" action, perform the following steps: 1. Open Cloud-based Services Configuration website (/config), log in as Integrator or Config Agent. 2. Enter the related Account 3. Click tab 'Actions'. 4. Click '+' button to add an action. 5. Give the action a descriptive name and select 'Relay'. 6. Select activation mode and select one or more relays to switch. 7. Click 'Create'. 8. Add the action to a Service Scenario for processing.   6. Notify Monitoring Center and Log Event Both action types "Notify Monitoring Center" and "Log Event" are obsolete and can not be used in a Service Scenario.  See also: How to add a user to Remote Alert service in Remote Portal?
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist