Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 
    Sort by:
    100% helpful (1/1)
    2 weeks ago
    This article gives an overview of CPPs that correspond to certain types of cameras, decoders and encoders.
    View full article
    100% helpful (2/2)
    ‎07-26-2024 12:37 PM
    This article contains the options for physical/ default reset of Bosch Inteox cameras.
    View full article
    100% helpful (1/1)
    ‎09-26-2024 07:41 AM
    New generation of Bosch cameras: no default password, the user has to create one
    View full article
    ‎07-29-2024 10:05 AM
    Intelligent Video Analytics (IVA) Pro provides application-specific packages for building security and operations (IVA Pro Buildings), perimeter security (IVA Pro Perimeter), and traffic monitoring (IVA Pro Traffic). While some of the IVA Pro variants are included by default on supported cameras, others can be added via licenses. This article is dedicated to describing the license process in full.
    View full article
    ‎09-26-2024 10:31 AM
    Find out in this article the Bosch Inteox cameras portfolio with the New Features
    View full article
    ‎07-26-2024 12:40 PM
    This article explains how to configure the Bosch ITS and NTCIP licensed versions of IP moving cameras to respond to National Transportation Communications ITS Protocol (NTCIP).
    View full article
    ‎09-26-2024 10:18 AM
    Find out from this article how can you avoid the MIC Inteox & Starlight 7100i camera wipers getting stuck.
    View full article
    ‎09-26-2024 09:02 AM
    This article shows how  the image quality of AUTODOME inteox 7000i & comparison with AUTODOME 5000i IR camera image can be improved.
    View full article
    ‎09-26-2024 12:48 PM
    The Dashboard has a Maximum temperature that exceeds 80 Degrees C and the camera will display "Status 8" when the internal temperature is above 80 Deg C.
    View full article
    ‎09-26-2024 09:47 AM
    If  ‘Calibration upload to camera failed’ for CPP7.3 & CPP13 Bosch cameras please follow the below steps: Upgrade Configuration Manager to version 7.61. This must be used in combination with CPP13 Firmware 8.45 or later  
    View full article
    ‎09-26-2024 12:42 PM
    Question Why the Autodome 7000i INTEOX cannot connect to the S&ST Cloud services?   Answer Most likely, when you tried to connect to the S&ST ecosystem, you missed one of the steps explained in this article: How to connect a Bosch INTEOX camera to S&ST using Configuration Manager?   If you are sure that you have followed correctly the steps from the article above, please collect from camera: Diagnostics logs Config file with log in credentials Event logs How to collect logs from your Bosch IP Camera/Encoder? Please check if the the following message is displayed in the logs: ✅ Tip "Not connecting (CC enabled: true; Network connection: true; MQTT client ready: true; NTP enabled: false)" → this indicates that you didn't turn on the NTP which is a prerequisite to connect to the cloud back-end  Please enable the timeserver and make sure the time of the camera is synchronized with a public time-server when connecting to the S&ST cloud.   Note: NTP synchronization is necessary if the camera is going to be claimed in the portal. Please refer also to the Help & Support page:  Claiming cameras
    View full article
    ‎09-25-2024 03:16 PM
    This article presents the considerations that should be taken into account when using the conduit adapter NDA-3080-CND for installation: For protection against water ingress we recommend to avoid top entry for the conduit adapter and use the side and bottom entry position Mark the position of the hole of the surface Drill the hole with the appropriate diameter drill Install a plug in the hole Put the cable through the hole of the conduit plate Attach the conduit plate with the conduit plate adapter to the surface Install the conduit cover on the conduit plate. Tighten the two screws with the TR15 Allen key
    View full article
    ‎10-02-2024 12:01 PM
    Due to an error in the software interface to the secure element chip on the cameras, the chip can be permanently damaged. Follow this article and find out the mitigation of this behavior
    View full article
    ‎09-26-2024 01:07 PM
    This article answer to the question: "Why the ‘SD card Status’ is missing in GUI of MIC IP starlight/ultra/inteox 7100i camera?"
    View full article
    ‎07-25-2024 03:00 PM
    This is a known design limitation and has always been present in the mentioned platforms. There are also no plans to correct this behavior.
    View full article
    ‎07-25-2024 01:52 PM
    Unsupported camera model: Auto-calibration is currently not supported for this camera model. Calibration could produce wrong results or might not work. Why is this message displayed in Configuration Manager?
    View full article
    100% helpful (1/1)
    ‎07-26-2024 01:22 PM
    Preventing condensation on security cameras is crucial because it can obstruct the camera's view, affecting its ability to capture clear footage. Over time, moisture build-up can potentially damage the internal components of the camera, affecting its functionality and lifespan
    View full article
    ‎08-16-2024 10:43 AM
    What FW versions did Crowd Density Estimation get removed from IVA Pro? What to use in replacement for Crowd Density Estimation? How to remove the unrecognized task?
    View full article
    ‎07-25-2024 02:58 PM
    This article provides possible causes and solutions regarding FLEXIDOME Inteox 7100i (CPP13) - calibration lost using FW 8.45.0032.
    View full article
    ‎07-25-2024 02:17 PM
    The Image Stabilization cannot be used in combination with VCA tasks, with the various MIC-7100i models. Turning Off the image stabilization will solve this behavior.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist