Security: Video

Please note that this recommendation might help, but cannot guarantee the high quality of the image. It depends on the camera FoV and the environment where the camera is installed.

This article provides the following solution regarding: Bosch CPP7.3 cameras: DHCP does not follow the standard protocol (FW v7.85.0016) Upgrade your camera to FW 7.86.0019 and perform a factory default (access Download Store here). The time effort to fix this in older FW will be planned for early March 2023.

This article contains the CGI commands that help you to enable or disable the MIC 7100i/MIC 7000i/MIC fusion 9000i camera's Wiper during boot-up

This article describe how to configure your camera to get optimize focus as-well during the day as night

This article provides a solution to the intermittent focus issues for MIC 7000i series and for the Optical video in the MIC 9000i

With fw7.70 a new feature was introduced that allows you to tune the scene for Day and Night separately using 2 custom scene modes. This article explains how to switch the scene modes Custom mode#1 & Custom mode#2 based on Day or Night for Bosch cameras

Find out from here what is VCA (Video content analysis) and how you can stop this setting.

This article explains how to fix the behavior of MIC IP 7000i/9000i Bosch camera when is out of focus during a rapid zoom

This article provides a step-by-step guide about how you can disable UPnP of Bosch IP cameras & multicast scan from Configuration Manager. One of the reason why UPnP (Universal Plug and Play) is enabled in our devices is because ONVIF uses this to scan the ONVIF device in the network.

This article gives an overview of CPPs that correspond to certain types of cameras, decoders and encoders.

If you are wondering where can be configured the field of view and focus of the FLEXIDOME IP starlight 8000i, without having to touch the camera or lens, this article will provide you the answer. 

For certain conditions, MIC cameras will display status codes on the video image. What does "status 9" mean on the MIC IP ultra 7100i │ MIC IP starlight 7100i camera's web page ?

All of camera block FW updates require an additional step for the FW upgrade process, which is described in the documents attached.

PTZ camera (Autodome IP starlight) doesn't move in Pan or Tilt direction. This is a basic troubleshooting guide that will help you to fix this issue.

The thermal mode is saved in the preposition settings. If you have changed the thermal mode of the camera in the Picture Settings Thermal page and you also want the Thermal color mode to apply to the existing saved pre-position, you have to re-save the pre-position again.  

The inconsistency in the tamper detection functionality could be due to various factors. Follow this article for more details.

Be sure that the MIC-7100i camera is configured in BVMS Configuration Client with "Bosch-AutoDome Bilinx" protocol and not with "Bosch-AutoDome" protocol or other options from the list.

Please note that the relay output of the IO Alarm card is a dry contact relay (with 24VAC/VDC, 5 A). In order to control another circuit that has a 230V you can't do that directly because its higher than it was design for. In order to safety control a 230V, you could use a 24V on that output and control an additional/external relay: powering its coil this relay could switch the 230 circuit of the washer.

In the winter period, if there is no PAN functionality in the camera and despite this, the TILT still works, this could be caused by the snow or ice that might be stuck between the static part of the camera and the moving camera head. Find out from this article how you can prevent this happening.

Bosch requires the installer to provide the specified power mentioned on the product spec sheet and labels. While taking into consideration the POE standards. Bosch doesn't support out-of-spec operation of our cameras as we cannot guarantee proper functionality in such circumstances. Thus, we will not be providing out-of-spec voltage or power values at this stage.