Security: Video

The purpose of this article is to help you find the customer number and the material/ serial/ commercial type number of your Bosch device in different ways.

The purpose of this article is to provide the step-by-step process of adding drives to a DIVAR IP 7000 R1 (DIP-7080-00N) Recording appliance and configure initial RAID setup on it.

Japanese characters in file names are displayed as garbled text after you decompress a .zip file in Windows 7 or in Windows Server 2008 R2.

This article provides a  solution  in case of memory leak on a Divar IP 7000 R2 triggered by Catalyst Control Center.

This article explains how you can solve the situation when Config Client shows Access denied message under the Physical capacity field, when trying to access the DIP-7000 AIO.

This articls provides the steps to update a DIVAR IP system. The firmware version 3.180.05-1562 can be used with the LSI MegaRAID Controller. 

The DIVAR IP units are prepared from production to use at first setup the port 8454.

The method from this article shows you how to generate an updated certificate for Bosch IP Camera's and VRM Servers

The purpose of this article is to provide a step by step guide about how to perform backup and recovery procedures of the VRM data base in the DIVAR IP 2000 EZ Recording Appliance.   Step-by-step guide Backing Up the Working Configuration: 1.To backup the working configuration of a DIVAR IP 2000 Recording Appliance, open the Appliance's "Dashboard": 2. From the Dashboard select the "Configuration" tab in the top right hand portion of your browse:

This article will guide you how to remedy invalid expansion licenses on your Bosch Divar IP 5000 all in one.    Error indication Despite that the registration of your additional purchased licenses has been completed successfully. The licenses may become invalid  after a  following reboot. This behavior is caused by switching the MAC address of your teaming interface.  

Answer It only depends on the version of BVMS you have. If you have BVMS 7.5, certain cameras with a certain FW have been tested and are supported. If you have BVMS 8.0, certain cameras with a certain FW have been tested and are supported. For BVMS versions of 9.0 or lower, only tested cameras must be added, otherwise we cannot support new setup. On DIP 3000 you can only upgrade to BVMS 8.0. The version of Windows installed on it does not support older versions of BVMS, it is not compatible. Recommended to use BVMS 8.0, the largest version supported on that unit. You need to make sure that those cameras are on the list of tested devices of the version you have.   Regarding the ONVIF Compatibility of the cameras, please see the following Bosch Knowledge Base article: https://community.boschsecurity.com/t5/Security-Video/BVMS-ONVIF-Device-compatibility/ta-p/4252

The following procedure describes how to restore DIVAR IP 5000 ALL-IN-ONE to the factory default image.   Step-by-step guide   1. Start the unit and press F7 during the BIOS power-on-selftest. The Recovery menu is displayed.   2. Select one of the following: – Initial factory setup: restores to factory default image and deletes all data on the HDDs. or – System Recovery (back to Factory Defaults): restores to factory default image; data on the HDDs will not be deleted.   Note: While the System Recovery option doesn't delete video footage stored on the data HDDs, it still replaces the complete OS (operating system) partition (including VMS settings) with a default configuration. In order to access existing video footage after recovery, the VMS configuration needs to be exported before System Recovery and re-imported afterwards.   Notice! Do not turn off the unit during the process. This will damage the Recovery media.   3. The unit starts from the Recovery media. If the setup is successful, press OK to restart the system.   4. Windows performs the initial setup of the operating system. The unit restarts after Windows has completed the setup. 5. After the restart of the unit, the factory settings are installed. 6. After the system has reboot, the next step is to change the BVRAdmin password. The default one is WSS4Bosch.

This article provides you with information related to the Windows Firewall, how to access, configure and adjust it.

The Divar AN 3000/5000 features the ability to ping an IP address, thus allowing the technician to verify that the workstation that is to connect to the Divar can be seen on the network. Please note that this only checks the connection from the DIVAR to the Workstation. Ping operates by sending Internet Control Message Protocol (ICMP) echo request packets to the target host and waiting for an ICMP echo reply. The program reports errors, packet loss, and a statistical summary of the results.

This article will explain how to set-up the RAID quickly in order to start the "re-imaging" process from the Recovery DVD (one at DIVAR IP 6000 R2 - or two DVDs at DIVAR IP 7000 R2) enclose to each DIVAR IP 7000 R2 or DIVAR IP 6000 R2 delivery. 

Question   Why the Windows license key and System ID are the same on all my DIVAR IP 6000?   Answer   These units come pre-licensed from the factory and they have an OEM (Original Equipment Manufacturer) license activated. Please see more information about OEM on the Wikipedia link below:  https://en.wikipedia.org/wiki/Original_equipment_manufacturer According to its datasheet, all components relevant to the usage of DIVAR IP 6000 as storage array in a Bosch recording solution are pre-installed and preconfigured. Simply connect to the network and power the unit up — DIVAR IP 6000 is ready to begin recording straight out-of-the-box.

The Windows Storage Server operating system of DIVAR IP all-in-one 7000 is installed on a two SSD drives in redundant (mirrored) configuration. Health status of the mirrored OS drives can be monitored using a tool called Virtual RAID on CPU (formerly known as Rapid Storage Technology). Installation and configuration steps are described below. Step-by-step guide   1. Installation: Download the setup from here Copy the content to a USB drive When the BVMS default screen is shown, press CTRL + ALT + DEL Hold down the SHIFT key while clicking Log off Log in as BVRAdmin Transfer the IATA_CD.exe from the USB drive to the BVRAdmin desktop Double click the IATA_CD.exe executable Follow the installation procedure as shown in the screen shots     2. Email notification: Note: The E-mail notification feature is based on SMTP access without authentication. It is strongly suggested to use this functionality only with a dedicated server in the local network, which is specifically configured for this purpose and doesn’t handle any critical data.

This article explains how to set an Unconfigured Bad Drive to Unconfigured Good on a DIVAR IP 6000/ 7000. This step is required if the new drive is not listed under Unconfigured Drives. A possible reason for the Unconfigured Bad status is when a device that has not been removed properly is reconnected to the controller.