Security: Video

The System Overview and Dashboard page shows all available data of your camera.  Find more useful information about FLEXIDOME multi 7000i camera from this article!

The “inactivity” algorithm from this article will move the camera to Pre-position 99 in the Alarm Task scripting.

This behavior was improved with the release of Video Security Client/App 3.2.3.

RAID 5 provides basic fault tolerance with good performance, but it cannot protect against multiple drive failures. RAID 5 with a hot spare improves fault tolerance by automatically replacing failed drives, but it still has the same limitation regarding multiple drive failures. RAID 6 offers a higher level of fault tolerance by using double parity, allowing for the simultaneous failure of up to two drives without data loss. However, it has higher write overhead and requires more drives for implementation compared to RAID 5.

Not all Cisco PoE+ switches are able to power up the UHO-PoE-10 or VSP-UHO-PoE-10 outdoor housing (F.01U.300.502, F.01U.332.052). Bosch has introduced the UHO-PoE-10 in 2014 following the IEEE802.3-2009 standards

NetApp SANtricity Dynamic Disk Pools (DDP) technology represents a significant advancement in storage system, data protection and data management. As disk capacities continue to grow without sufficient increases in data transfer rates, traditional RAID rebuild times are getting longer, even up to several days. This slow rebuild results in much more time with degraded performance and exposure to additional disk failures.

One of the possible traps  that DIVAR IP hybrid/network can send is HDD_STATUS_CHANGE. The HDD_STATUS_CHANGE is triggered when the status of the Hard Disk changes. 

The URL for RTSP stream (for example in VLC Media Player) should have the format as described in this article

When camera is set to auto track (by web interface) to "auto"-> IVA is detecting an object but camera is not following. Auto tracking works and metadata is displayed only on a stored preposition.

‘Display stamping’ submenu has been moved from the General menu to the Camera menu.

If you want to improve the image quality of your Bosch camera and you did not find the FPS option in the Web User Interface, please follow this article and you will find the answer.

If you are wondering where can be configured the field of view and focus of the FLEXIDOME IP starlight 8000i, without having to touch the camera or lens, this article will provide you the answer. 

If you were asked by the Central Technical Support team to provide them with the Sensor readings picture during the troubleshooting process of your device, please follow the steps from this article

Importing a foreign configuration should recover a RAID configuration (in case the RAID is not corrupt) This option must be performed before creating a new VHD. This option may restore all of the video and data on the drives.

If you were asked by the Central Technical Support team to provide them with the Bios defaults picture with the Boot order of your DIVAR IP during the troubleshooting process of your device, please follow the steps from this article and find out how can you check the boot order of a DIVAR IP

This article contains 2 options describing the way you can find the Firmware version of your DSA unit, in case the Central Technical Support team is asking you about it or if you simply want to find it by yourself. Check out this article!

To access the "Reset" options of a DIVAR IP 2000 Recording Appliance, you have to open the Appliance's "Dashboard".

The purpose of this article is to assist you with the creation of mirrored drive sets in a DIVAR IP all-in-one 5000 Recording Appliance.This procedure should be performed on new appliances that have not yet been deployed.

🛈 Port Forwarding Allows remote computers (for example, computers on the Internet) to connect to a specific computer or service within a private local-area network (LAN). In a typical residential network, nodes obtain Internet access through a DSL or cable modem connected to a router or network address translator (NAT/NAPT). Hosts on the private network are connected to an Ethernet switch or communicate via a wireless LAN. The NAT device's external interface is configured with a public IP address. The computers behind the router, on the other hand, are invisible to hosts on the Internet as they each communicate only with a private IP address. When configuring port forwarding, the network administrator sets aside one port number on the gateway for the exclusive use of communicating with a service in the private network, located on a specific host. External hosts must know this port number and the address of the gateway to communicate with the network-internal service. Often, the port numbers of well-known Internet services, such as port number 80 for web services (HTTP), are used in port forwarding, so that common Internet services may be implemented on hosts within private networks.

This article provides you with the available options, services and licenses in Bosch Remote Portal for Bosch IP cameras.