Security: Video

The "Import" icon may be missing from table view in Configuration Manager, version <7.50. Therefore, we recommend to update the Configuration Manager to v7.50

To be able to deploy a camera with DHCP disabled to Bosch Remote Portal, please perform the steps from this article.

BP+ (Baseline Profile +) is available in any of the new ARM based chipset encoders, like the VIP-X1 XF.  BP+ is needed for compatibility with Divar and hardware decoders, for example, theVIP XD decoder.

This article shows what to do in case the following message occurs: "Could not add the following devices"  when adding IP cameras FW 7.87  to BVMS 12.0.

Answer It only depends on the version of BVMS you have. If you have BVMS 7.5, certain cameras with a certain FW have been tested and are supported. If you have BVMS 8.0, certain cameras with a certain FW have been tested and are supported. For BVMS versions of 9.0 or lower, only tested cameras must be added, otherwise we cannot support new setup. On DIP 3000 you can only upgrade to BVMS 8.0. The version of Windows installed on it does not support older versions of BVMS, it is not compatible. Recommended to use BVMS 8.0, the largest version supported on that unit. You need to make sure that those cameras are on the list of tested devices of the version you have.   Regarding the ONVIF Compatibility of the cameras, please see the following Bosch Knowledge Base article: https://community.boschsecurity.com/t5/Security-Video/BVMS-ONVIF-Device-compatibility/ta-p/4252

Sometimes it is preferable to have a different “user mode” during the day then in the night. Our cameras by default have the option to switch the user mode e.g. triggered by the camera D/N switch over. But also other triggers can be chosen. Below an example how to setup the “user mode” switching triggered by the D/N switch over.

Maintaining the highest level of data security requires continuous improvements in all the system components - including software and device firmware. Recent changes in the camera firmware are focused on improving the security level overall.

The RTC_AUDIO_LOUDSPEAKER_ON_OFF flag is not activated.

Before asking for assistance, please collect and provide the Central Technical Support Team with the information from this article.

In principle, the Autodome starlight 5100i IR camera (NDP-5523-Z30L) may only be operated with switches, midspans or PoE injectors that meet the EEE802.3bt standard! - Or use 24VAC.**

This article explains how you can change the IP Matrix Passcode PIN when using Configuration Manager version lower than 7.50 & VIDEOJET decoder 7000 (VJD-7513) FW version lower than 10.22.

When it comes to maintaining your system uptime, you absolutely have to know when there's a problem, no matter where you are or the time of the day. Therefore, this article helps you learn how to enable Remote Alerts, if something happens on the site and you are not on it.

This only happens when you perform the export in BVMS Operator Client.

This article explains how to use the settings as per the devices current configured capabilities if you just added a device to BVMS, you get the possible stream options as per a “Config table” known to BVMS.

This article explains what action should be done for DIVAR IP 7000 Gen 3 before collecting IPMI logs

  What does mean the clock symbol showed in the Operator Client Logical tree?

At first sight, you might think that the model is the correct one that shows in the Datasheet, but the Video card is smaller than the DIP Slot.

This article explains what you shoud do when the display output suddenly shows “System Initializing 91” message on screen, while you are turning on your DIVAR IP 7000 R2

This article presents what are the limitations of Privacy overlay in BVMS 12 (Pano cameras, h.263 & MPEG, decoder, VSC).

This article contains a simplified and generalized example, that could be helpful in building a particular tailored script related to implementation of event receiver in BVMS SDK scriplet.