Security: Video

An object moving or a low/ higher contrast scene can throw off the autofocus option, resulting in a soft focus or even not focus at all. Using manual focus is an obvious solution, but manual focus isn’t exactly easy to get sharp images. Manual focus requires a bit of know-how and some practice to get right. If you would like to improve the performance and get a sharp image, please see below how you can manually adjust the focus ring on a Dinion Thermal camera.

Please find in this article some settings you can do separately for each FLEXIDOME multi 7000i camera imager on the camera’s web page.

Check this article and find out how can you fix the bad frozen image and no PTZ, bad images, uncontrollable web-interface, stuck images in Genetec live/recording for AUTODOME IP starlight 7000 HD camera (FW 7.10.0076) integrated in Genetec as VMS. Version 5.9.4

This article shows how  the image quality of AUTODOME inteox 7000i & comparison with AUTODOME 5000i IR camera image can be improved.

Some options have been removed when compared to previous CPPs, as they are only useful for moving cameras. Find here the overview of the web page of ‘Live’ functions section and the options remained available for FLEXIDOME multi 7000i (CPP14) cameras.

If you are wondering where can be configured the field of view and focus of the FLEXIDOME IP starlight 8000i, without having to touch the camera or lens, this article will provide you the answer. 

‘Display stamping’ submenu has been moved from the General menu to the Camera menu.

The System Overview and Dashboard page shows all available data of your camera.  Find more useful information about FLEXIDOME multi 7000i camera from this article!

Follow this article if you would like to optimize the image quality of your AUTODOME IP 5100i camera

New generation of Bosch cameras: no default password, the user has to create one

In principle, the Autodome starlight 5100i IR camera (NDP-5523-Z30L) may only be operated with switches, midspans or PoE injectors that meet the EEE802.3bt standard! - Or use 24VAC.**

This article explains step by step how to remotely connect to DIVAR Network or Hybrid via Divar Mobile Viewer App

Both RJ45 and M12 plug connectors are available with IEC 11801:2002 Cat5 compliance. This further simplifies the concurrent use of both connector types within a single system.

This article presents the considerations that should be taken into account when using the conduit adapter NDA-3080-CND for installation: For protection against water ingress we recommend to avoid top entry for the conduit adapter and use the side and bottom entry position Mark the position of the hole of the surface Drill the hole with the appropriate diameter drill Install a plug in the hole Put the cable through the hole of the conduit plate Attach the conduit plate with the conduit plate adapter to the surface Install the conduit cover on the conduit plate. Tighten the two screws with the TR15 Allen key

Flexidome 8000i or other future cameras with WLAN option enabled (default ON) in an IPv6 network environment: no IPv4 possible. What to do?

This article contains the CGI commands that help you to enable or disable the MIC 7100i/MIC 7000i/MIC fusion 9000i camera's Wiper during boot-up

PTZ camera (Autodome IP starlight) doesn't move in Pan or Tilt direction. This is a basic troubleshooting guide that will help you to fix this issue.

Intelligent Audio Analytics feature is available for FLEXIDOME 5100i panoramic cameras. This feature is available on camera firmware starting with version 8.80.

If the CPP6, 7 and 7.3 cameras no longer have a live image or there is a delay in the image, and the Internet connection has been tested and is within normal parameters, it would be good to check if the cameras have the latest current firmware version 7.86.0020. This firmware version solves a 100% CPU load issue for CPP6, 7, 7.3 from firmware 7.82 to 7.86.19

Depending on the case, you can use the RS pins in various scenarios. If you wish to send information from the camera to an external device, you must use the Tx pins.