Security: Video

When the camera operates in automatic Night-Mode and the switching interval is too fast the camera built in protection mechanism will intervene to prevent premature wear of the mechanical IR-Cut filter.

This article describes how Streamlining works and how it can be finetuned.

Configuration Manager 7.60 by default will only trust CA signed certificates. Changing the security requirements will change the behavior of how CM displays the connection/access.

"Show VCA items" is a function which works in Internet Explorer 11 with the Bosch MPEG ActiveX installed. Due the end-of-life of Internet Explorer, this function is no longer available on Microsoft Edge.

This article shows how to configure Input Alarm and later search for them in the Event search using Web Interface.

This article describes all the steps that will help you to create iSCSI Virtual Disk/LUNs after replacing an HDD on a DIVAR IP 5000 AIO.

There are two methods of working with 3rd party apps: through Remote Portal and Configuration Manager. In this article you will find the step-by-step guide where is described the method using Configuration Manager.

Monitor Group gives operators flexible control over the content of a video wall or allows them to let the system take over this control automatically based on pre-defined scenarios. This article describes how to create a Monitor Group on a decoder VJD 7xxx/ 8xxx in BVMS Configuration Client

The latest suitable Image for your DIVAR IP R2 Family Device can be obtained from Bosch Central Support Team. Please provide the SN (serial number) from the DIVAR IP 6000/7000 R2 when contacting Bosch Central Support Team.

This article contains all the steps to restore DIVAR IP 7000 R2 to factory default. Note: By performing the Initial Factory Setup on the system, ALL DATA from the ENTIRE system will be erased.

If you are interested in retrieving the stream of an IP camera using multicast, please check out the options from this article.

This article describes how to set LUNs on a target to Read Only via Configuration Manager.

From this article you will find out how to set up the IP Matrix configuration on the VIDEOJET decoder 7000 (VJD-7513) using Configuration Manager.   The built-in IP Matrix functionality, together with a connected keyboard, allows VIDEOJET decoder 7000 to run as a stand-alone system. An operator can manage up to 32 cameras via the keyboard without any PC or management system required. System setup is quickly done with Configuration Manager. After that, no PC is required to run the IP Matrix   Note: According to the Release letter (Firmware 9.51) of VJD-7513, VIDEOJET decoder 7000 supports IP Matrix application as built-in feature. According to the Release letter (Firmware 54.8.02) of VJD-7000, IP matrix remote monitor is only possible with UDP. TCP not supported. ** VJD-7000 can be used as an extended monitor to IP Matrix in single and quad view. Please check also the following article and find out: Which are the system requirements for configuration/ operation of VIDEOJET decoder 3000/ 7000/ 8000?   A single system can support: 2 physical monitor displays One KBD-Universal XF keyboard 32 cameras 32 camera sequences 9 favorite views

In this article you can find the actions you need to do in order to solve the zoom speed for AUTODOME NDP-7512. A customer could observe a difference in zoom speed in comparison to the previous generation

Intelligent Insights support controlling Bosch IP cameras by Common Gateway Interface (CGI) commands over HTTP or HTTPS when a threshold of the area fill level, area fill level traffic light or occupancy use case is reached. Follow the step-by-step guide below and find how you can to setup the threshold actions in Intelligent Insights.

The Clear button on the Configuration Manager is designed to clear the codes that are self-generated by the IP firmware or the Configuration Manager itself. Follow the steps below, if you want the "Clear" button from Configuration Manager to able to erase the Alarm task script that are self created by users themselves.

This guideline will help you set the position of the camera  image to an appropriate one. If the picture of the camera is inverted in the live view, please follow the steps below to reverse it.

If your DINION IP Thermal 8000 (NHT-8000) camera is reporting blurred/unclear/unsharp images that are randomly appearing during the day, or the night, please follow the steps below in order to fix it.

This article provides the step-by-step procedure on how to configure “BVMS” presets and save views.

VSG is specifically designed to provide integration for 3rd party ONVIF, JPEG, RTSP, and legacy H.263 Bosch devices.