Security: Video

To ensure the highest customer satisfaction and replace the defective hardware faster and more smoothly, it is necessary to register each system for the specific country together with the system location. But where and why should you register your device?

The Virtual Assistant event is mapped to code 751 in the alarm transmitter. It is not possible to differentiate in the alarm transmitter the different scenarios on which an event code should be customized. The event properties sent from the Alarm Management application to the transmitter contains only if it's a VIRTUAL ASSISTANT or LIVE INTERVENTION etc.

If you have configured an out of the box system and once the configuration was done you wasn’t able to access the BVRAdmin account, this article will help you to find a solution. Access to BVRAdmin account is required to perform administrative tasks on the operating system. This requires the following steps:

This article describes how to configure a generic Microsoft Windows Server (2012 R2, 2016 or 2019) based server to serve as an iSCSI target for a Bosch video surveillance environment. SCSI (Small Computer System Interface) is most commonly used for the communication between computers and peripheral devices, such as hard drives. iSCSI enables devices to use SCSI over a network interface, therefore it makes a lot of sense for cameras to use iSCSI to record video. The camera is a small computer that needs a (network) connection to a "hard drive" to store video footage. In other systems this job is performed by the network video recorder (NVR).

There might be problems when you are trying to use the Forensic search function for FLEXIDOME Multi 7000i cameras (FW 8.71.0066) after upgrading from BVMS 10.1 to BVMS 11.1.1.65. The message is saying that “Forensic search must be configured for this workstation”

When looking at the MQTT explorer, the naming of the counters is always as in the first camera, so always "Counter-1-1" and "Counter-1-2".

Check this article to learn about what to do when a FLEXIDOME multi 7000i (IR) or FLEXIDOME panoramic 5100i (IR) does not boot up or is unresponsive.

Find out from here what to do if your FLEXIDOME Multi 7000i or FLEXIDOME Multi IR is coming offline sporadically/ disappears from the network

This article contains several common questions and answers about Firmware of Bosch MIC IP Starlight 7000i cameras

Find out what can you do when in large parts of the zoom range, the MIC IP starlight 7100i camera simply does not focus; this is the same for manual PTZ and pre-sets.

This article helps you to find a solution for your MIC IP ultra 7100i (CPP 7.3 ) when front end is not available after FW upgrade from 7.62.0005 to 7.70.0126

This article provides a solution to the intermittent focus issues for MIC 7000i series and for the Optical video in the MIC 9000i

All of camera block FW updates require an additional step for the FW upgrade process, which is described in the documents attached.

The MinIris and MaxIris values could be configured when the camera is mounted and installed in specific lighting conditions.

DIP serial number can be found in 2 ways. IPMI information cannot be found within the software and is provided on the device itself. It can be found next to the BMC/IPMI port on the back of the device.

In this article can be found which is the max. iSCSI recording sessions of DIVAR IP AIOs.

This article explains how to fix the behavior of MIC IP 7000i/9000i Bosch camera when is out of focus during a rapid zoom

See what you can do when MIC 7000i with FW 7.72 shows blurred images. After restart, the quality of the image is good for a short time, but the issue reappear.

How to detect in an easy and convenient way if the camera suffers from a failing shutter mechanism which can result in white or ghost images? This article helps you to identify if the camera possibly suffers from a random failing shutter which uses the FFC (Flat Field Correction) instead of waiting for the FFC taking place approx every ~10min, you can now fire it on command.

Equipment should be mounted into a rack so that a hazardous condition does not arise due to uneven mechanical loading.