Bosch Building Technologies

    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    ‎04-05-2021 04:09 PM
    This information  may be requested by Central Support Team, as the bundle file is useful for troubleshooting the improper behavior of the unit. The method for collecting the NetApp DSA E2700 support bundle file is provided below.
    View full article
    ‎04-05-2021 04:30 PM
    If you are interested in retrieving the stream of an IP camera using multicast, please check out the options from this article.
    View full article
    ‎04-05-2021 04:34 PM
    In this article you can find the actions you need to do in order to solve the zoom speed for Autodome NDP-7512. A customer could observe a difference in zoom speed in comparison to the previous generation. HDR was OFF by default in the 7000, But is ON by Default in the 7000i which has effect on the zoom speed. Therefore, disable HDR to obtain the zoom speeds that match the previous generation of the camera.
    View full article
    ‎04-05-2021 05:18 PM
    If you want to control the camera from a DIVAR wired through a VJD 3000, you have to configure the VJD and the DIVAR as well. Below you will find the steps which will help you to set up your devices.
    View full article
    ‎10-26-2021 11:18 AM
    This recommendation could be applied if the storage is overloaded, as there are several Onvif cameras running through it.
    View full article
    ‎06-14-2022 10:54 AM
    Our portfolio contains quite a variety of (mobile) video clients and applications. To get a fast first overview we created the attached table to compare the most important ones.
    View full article
    ‎12-16-2022 09:13 AM
    This article is focused on a method of creating a new profile with own parameters and make this new profile active.
    View full article
    ‎06-22-2022 12:17 PM
    This article describes how can you check the status of your Software Maintenance Agreement (SMA) for Bosch Video Management System (BVMS)
    View full article
    ‎04-05-2021 04:08 PM
    This article describes how can you disable password Policy for Cameras/ Encoders and provide compatibility with older/ 3rd party systems.
    View full article
    ‎08-18-2021 09:09 AM
    This article describes how a Tattile camera can be connected to BVMS. We recommend keeping the Tattile camera documentation and BVMS configuration manual at hand to fine tune the system configuration to the specific needs of your project   Configuration: This article helps you to configure three aspects: Match list configuration: the Tattile cameras can load a license plate match list from an FTP server. This article describes how you can enable an FTP server on the BVMS management server and use this as a source of the license plate match list. Camera configuration: the Tattile camera itself requires specific settings before it can be added to BVMS. BVMS Configuration: adding the Tattile camera to BVMS.   Check list configuration Tattile cameras can have up to two check lists: A and B. This article helps you to configure check list A based on an FTP server running on the BVMS management server. The article is written based on Windows Server 2019 but can also be used Windows Server 2016 and Windows Server 2012 R2 as they look and feel similar.   Step-by-step guide   1. Setting up an FTP server on the BVMS management server Open the Internet Information Services Manager and add an FTP site to the local server. You can give the FTP site an arbitrary name. The physical path needs to be accessible for a user with both read and write access on the file system as well as via the FTP site. The FTP site should not be configured with SSL. The other settings can be adjusted based on the security-level of the installation. The security-level can be increased by applying, for example, IP filtering on the FTP site or in the Windows Firewall. This way, only configured cameras can access the FTP site. The FTP site uses Basic authentication. This means that the FTP authentication uses the Windows authentication mechanisms in the background. Users (cameras) should only have read access on the FTP site. This prevents unauthorized modifications of the match list. Use the computer manager to create a special user, for example, "ftp_user". This user should have read and write access on the FTP site folder and on the file system.   Create a file in the FTP site, for example, BlackList.txt using Notepad. Save the file using UTF8 encoding: The contents of the file should match the following format: License plate; Country;Comments Please be aware that the Country identifier always consists of three letters. ### can be used as a wildcard and represents all countries AB134HK;ITA; Test BS46588;###; Substitute car RS054HG;ITA; President’s car   Test if you can open the file using your favorite browser by entering the FTP address:  ftp://ftpuser:password@x.x.x.x:21/ BlackList.txt. The username and password dialogue should not pop-up and you should have direct access to the content of the BlackList.txt file.   1.1. Synchronizing the check list in the camera with the FTP server Plate Reader => Check List => Check List A You should enable check list A and configure the List Location as FTP. The FTP IP should match the location of the IP address from the BVMS management server. The File Name should match the name of the file storing the check list. When you click Reload List, the List Loaded message should appear, including the number of license plates you have put on the list. Multiple cameras can point to the same check list. The checklist can also be generated by an external application that writes the file considering the required format. 1.2. Configure match list management from BVMS Operator Client BVMS operators can manage the check list from the BVMS Operator Client. The user account the operator uses to login to Windows needs to have read and write access to the file that the FTP server hosts. You can achieve this by creating a new shared folder or by using the existing (hidden) shared folder. In the example below we use an existing (hidden) share folder: c$. Use the BVMS configuration client to open the resource manager. Add a new resource, in our case, an external application. The external application launched notepad.exe and points to the location of the check list using an argument.   Add the external application to the BVMS logical tree. This way operators can access it when they want to adjust the check list. Of course you can also put the external application in a folder.   2. Camera configuration The Tattile camera can handle one admin connection simultaneously. As a result, you can add one camera to one BVMS system.   2.1. Add user System => HTTP Users Change the default usernames and passwords or add an additional admin user that BVMS can use to login to the camera.   2.2. Configure communication protocol System => Protocols => VRC BVMS communicates with the Tattile cameras using a secured protocol (VRCS). Configure the VRC server settings as indicated in the image below. System => Network Configure the IP address from the BVMS management server in the Static hosts section. The Names must state BvmsLpr_Server (case sensitive). If the Names does not match BvmsLpr_Server, in this dialog or in the events / action settings, the BVMS management server will not receive events from the Tattile camera.   2.3 Configure event and action settings Plate Reader => Events Actions The Tattile camera has several events and actions. We use two events: Ocr Read and Match On List A. Configure the Template Message for these events by clicking on the image.   You should configure both events in the same way using the example below. The  Server name/IP  must state  BvmsLpr_Server . The Text Value should state: %EVENT_DESC%PLATE_STRING%PLATE_COUNTRY%SN%UTC_DATE%UTC_TIME   Apply the changes. Plate Reader => Events Actions => Template Configuration (Config, bottom of the page) Additionally, you need to upload a template message. Click the  Upload Page  and load the file   C:\ProgramFiles\Bosch\VMS\Appdata\LPR_Event_Template.txt  on systems where the BVMS configuration client is installed.   2.4. Configure separator plate Optionally you can configure a separator plate for specific countries. This determines how the detected license plates are written into the BVMS logbook. The camera user manual contains more information.   3. BVMS configuration The BVMS configuration manual also describes how to add LPR devices to the BVMS configuration.   3.1. Add LPR camera Add an LPR device by right clicking on the LPR devices node.   3.2. Add video (RTSP) camera Some Tattile cameras also have a video output (Not possible for the basic family). You can add these cameras to the Video Streaming Gateway (VSG) configuration as an RSTP camera. Use the   rstp://x.x.x.x   without authentication to load the video stream into BVMS.   3.3. Configure LPR events You can use the Events and Alarms tab in the BVMS configuration client to configure the events and alarms. BVMS receives License plate detected (Ocr read) and License plate identified (Match On List A) from the camera. We recommend to configure an alarm on the License plate identified event and store the License plate detected event in the BVMS logbook.   3.4. Allow only users in the "Admin" group to manage license plates Some user groups might not be allowed to edit the check list. You can remove the rights by de-selecting the node in the logical tree on the User groups tab in the BVMS configuration client.   4 Operation Alarms from the camera are processed using the normal BVMS alarm management. The check list can be easily edited by an operator by dragging and dropping the Manage License Plates application into an image pane, editing the file, and saving it (either by CTRL+S or by clicking File / Save).   4.1 Alarm Handling If the License plate identified or License plated detected events are configured to trigger alarms, the following information will be displayed in an alarm: The standard BVMS alarm information as timestamp, event type, alarm title, triggering device, etc. The license plate itself The country identified (DEU for Germany, etc.)   4.2 Investigation / Reporting With the LPR events License plate identified and License plate detected stored in the BVMS logbook, it is possible to solve use cases as "When did a car enter and leave the premises". Open the logbook search in the Operator Client, define a search filter for the License Plate detected or License Plate identified event and run the search, if you want to get an overview of all detected plates. If you look for a specific number plate, you can additionally enter the license plate in the Text Data field. The results are listed below and can be exported using the Save results button.
    View full article
    ‎07-15-2022 04:24 PM
    This article describes the considerations that need to be taken into account when designing a video surveillance system that is suitable for person identification. 
    View full article
    ‎06-16-2022 02:28 PM
    The attached document provides more insights into the system configuration regarding the BVMS - Operator collaboration with Slack
    View full article
    ‎07-28-2022 02:26 PM
    This article describes the different possibilities - BVMS Operator Client and BVMS Viewer, VRM eXpport Wizard, Web Interface of a Bosch Camera. The choice of the tool depends on the way the camera and recording are managed.
    View full article
    ‎06-01-2022 11:55 AM
    In order to start to analyze and optimize Video Analytics settings for particular customer set up, we need initial information and export of example video. This article describes the absolute minimum information we need in order to start analyzing and optimizing Video Analytics performance. Video Analytics (VA) task performance optimization Please provide the following details:   Symptom specific Information   Problem Description   Describe the expected result from the VA task. It is important to get detailed information of the results VA should provide. Define what is the customer’s priority: High sensitivity - miss as few true alarms as possible, but increases the likelihood of more false alarms! High precision – have less false alarms, but accept the risk to miss true alarm! Using VA is always based on balancing between sensitivity and precision. It is not always possible to get high sensitivity and high precision at the same time.   Provide an export of recorded video that should contain: Meta data: for basic understanding of meta data, please read the latest Software Manual Video Content Analytics for instructions about doing a video export with meta data, please read the article: How to export video including meta data (Export video including Video Analytics meta data).   Couple of examples of false alarms (in case false alarms are the issue) Provide the number of false alarms per time span (per day, per week, etc.) What would be acceptable as a number of false alarms per time span   Couple of   examples of situation that should have caused alarm, but VA did not generate the alarm as expected. In this case please provide the time stamp of the event and short description   Screenshot from the Camera Calibration Verification page - only in case calibration is needed for the particular VA functionality  access the Calibration Verification page of the camera (via the Configuration Manager or Web Interface)  provide screenshot from the verification of each parameter used for camera calibration     Note:  For more information on Camera Calibration and Calibration Verification, please check: How To calibrate camera for Video Analytics?
    View full article
    ‎06-16-2022 09:51 AM
    This article provides a step by step description of how to create certificates and configure  their distribution in the large systems. 
    View full article
    ‎08-05-2021 05:29 PM
    Similar to VRM eXport Wizard 2.0,  encrypted and unencrypted VRM recordings can be exported (VRM block export) from any video surveillance system based on Bosch Video Recording Manager (VRM) and exported recordings can be converted to mp4-files.    VRM eXport Wizard 2.10 introduces a new look and feel of the graphical user interface and some UX changes. In general, the VRM eXport wizard is a software tool that allows you to export video directly from the VRM and to convert exported video data to mp4. You can find the VRM eXport wizard setup file in the VRM Master Installer or in the bonus directory of the BVMS zip file. Exports made with the VRM eXport Wizard 2.10 can be open in BVMS (Viewer) 9.0 or newer. In this document we describe how to use the VRM eXport Wizard for either export of video data and conversion of the exorted video data to mp4. With the VRM eXport Wizard 2.10 encrypted and unencrypted VRM recordings can be exported (VRM block export) from any video surveillance system based on Bosch Video Recording Manager (VRM) and exported recordings can be converted to mp4-files. Therefore, the VRM eXport Wizard 2.10 offers - similiar to the previous version - the following two options, compare also Figure 1: Export Video Recording Manger recordings of cameras Convert already exported data to MP4 files
    View full article
    ‎08-25-2022 10:29 AM
    "Project Assistant easily cut our camera installation labor by 30%"
    View full article
    ‎06-08-2022 08:09 AM
    Check this article and see what's new in Project Assistant version 1.4.1
    View full article
    ‎08-17-2022 03:41 PM
    The modern and easy to use Bosch Video Security Client version 3.2 provides you new features. Check out this article and find what's new!
    View full article
    ‎06-16-2022 03:16 PM
    Find out from this article if there are restrictions of VRM Configuration utility pre-installed on DLA
    View full article
    Top Contributors