Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    ‎09-03-2019 01:41 PM
    Dear users, have you ever wondered how to best transition from the Project Assistant to (B)VMS? This article aims at providing you a recommendation and the answer is quite simple: Use the Project Assistant to its full extent and once the cameras are connected to the target network, perform a network scan using the BVMS Configuration Client, to add the respective cameras to the system. The remaining fine-grained settings can then be tackled within BVMS.  For details, please check out the attached presentation. Let us know, if you have further questions and share your comments below. Best regards, Your Bosch Security App Team    
    View full article
    ‎01-15-2019 02:21 PM
    Version 1.2.1 has been released for iOS only. It resolves an issue when trying to connect wirelessly to a FLEXIDOME IP 8000i camera. There was an issue where the operating system blocked the Wi-Fi access.
    View full article
    ‎02-12-2019 02:16 PM
    The attached technical note describes idle and removed object detection with Intelligent or Essential Video Analytics in FW 6.30, how to configure it and what the limitations are.
    View full article
    ‎09-24-2019 09:39 AM
    Question What's new in version 1.3.1? Answer Dear users, thank you for working with the Bosch Project Assistant. Based on your feedback, we have introduced the following improvements and features to make its use even more effective and enjoyable: • Sorting option on project overview page • Easier and faster removal of cameras from a project • Time server support • Re-commissioning support for VRM-managed cameras (focus on Flexidome IP 8000i) • Configuration mismatch (between project/app and camera) resolution dialog • Integration of Bosch Portable camera installation tool (NPD-3001-WAP), i.e. automatic detection of its wireless access point, management of multiple tools, and configuration of the tool’s network settings within the app Please check out the updated article " How-to: connect to and configure the portable camera installation tool ". Here we have added new videos that help you to get started and which explain the sepcifics of the different platforms - iOS, Android and Windows. Enjoy! Your Bosch Security App Team PS: For details, please have a look at the latest release letter in our Bosch Security Download Area.
    View full article
    ‎02-12-2019 02:18 PM
    The museum mode of Intelligent and Essential Video Analytics is an optimized tracking mode to detect whenever someone tries to reach towards and touch a valuable asset like a museum exhibit. It can also be used in any other application where approaching a sterile zone from a more crowded environment shall be detected. The attached tech note describes when and how to use it with FW 6.30.
    View full article
    ‎02-12-2019 02:18 PM
    Object classification takes an object detected and tracked by either Essential or Intelligent Video Analytics, evaluates its geometric and speed properties, and decides whether the object is an upright person, a bike, a car or a truck. The technical note in the attachment provides an overview of object classification, describes how to configure it with FW 6.30, and what the limitations are.
    View full article
    ‎02-12-2019 02:17 PM
    The technical note in the attachment describes how to track ships using Intelligent Video Analytics with FW 6.30, how to configure this and what the limitations are.
    View full article
    ‎05-20-2019 04:54 PM
    Question What's new or fixed in Project Assistant 1.2.3? Answer This release concentrates on general stability improvements and bug fixes. We could address three findings thanks to your feedback: Keyboards on Samsung devices sometimes got stuck (Android only) Dropbox sync showed unexpected behavior when sharing a project Wireless Connectivity Flexidome IP 8000i: “Camera found nearby – connect” dialog although being properly connected to the camera already
    View full article
    100% helpful (1/1)
    ‎12-19-2019 08:33 AM
    Compared to hardware, in which it is relatively easy to define an end-of-support concept based on the expected lifetime, software behaves totally different. In theory, when the environment does not change, software can still be running ten years after it has been installed. As new versions of the software are released regularly, it is important for customers to know what they can expect from Bosch Building Technologies when the software is purchased. This document describes how Bosch Building Technologies handles the life-cycle of the BVMS, BIS, AMS, and APE, and in which state a specific release can reside. Additionally this document lists the up-to-date situation for all of those software packages.
    View full article
    ‎02-20-2020 10:35 AM
    Overview: The RAID combines two or more physical drives into a logical unit presented as a single hard drive to the operating system. There are currently six basic RAID levels: RAID 0, RAID 1, RAID 0+1, RAID 1+0, RAID 3, RAID 4, RAID 5 and RAID 6. The scope of this article is to provide basic information for the levels RAID 5 and RAID 6 and to compare them from point of view of performance and security.   Hot spare is a drive that acts as a stand by drive in RAID 1, RAID 5 or RAID 6 volume. It is fully functional drive that contains no data and is not used during normal operation. If a drive from the volume fails, the controller reconstructs the data from the failed drive to the hot spare drive. A RAID 5 array is designed to protect against the failure of a single disk within the array. Because of the way that RAID 5 works, the total capacity of one disk is lost to overhead. If, for example, a RAID 5 array contained five 10TB disks, then the array’s usable capacity would be 40TB. A RAID 5 (with Hot Spare disk) array can be configured to treat one of the disks as a hot spare. Then one of the disks is reserved as a replacement in the event that a disk fails. For the above example with five 10TB disks, this would decrease the example array’s usable capacity to 30TB. A RAID 6 array is designed to protect against two simultaneous disk failures. However, the price for this extra protection is that two disks' worth of capacity is lost to overhead. As such, a RAID 6 array made up of five 10TB disks would have a usable capacity of 30TB because 20 TB is lost to overhead. The performance during Normal Operation is measured in IOPS (Input/output operations per second) and as a sum for all the disks (excluding the Hot Spares and decreased for writing parity data) in the array.  As a rule of the thumb, the higher the overhead associated with writing parity data (in the above example RAID 5 with Hot Spare causes the same overhead like RAID 6) the lower the IOPS. The reason for implementing RAID arrays is to secure the data. The level of protection does not directly correlate with the overhead. From the above example both RAID 5 with Hot Spare and RAID 6 have same capacity, but offer different level of protection. In case of failure of RAID 5 array with Hot Spare, the Hot Spare is activated and the rebuild process start immediately. The system can recover from a single disk failure and during the recovery, process is vulnerable to second disk failure. Therefore, RAID 5 and RAID 5 with Hot Spare disk offer the same level of protection – single disk failure.  In contrast, if a disk fails at RAID 6 array, the recovery will start only after the faulty disk is replaced manually.  However, if during the recovery process second disk fails, the RAID 6 array will stay functional.  
    View full article
    ‎03-02-2020 02:58 PM
    Hardware change in FLEXIDOME IP 4000i 5000i causes update in minimum FW version 7.60
    View full article
    100% helpful (4/4)
    ‎10-02-2018 01:55 PM
    The BVMS Operator Cliet can be automatically logged in by using parameterized startup. For this, a new shortcut to the OperatorClient.exe needs to be created, and the target of the shortcut needs to be adjusted. The text between ** needs to be adjusted to the specific situation. "*BVMS installation directory*\bin\OperatorClient.exe" /user="*username*" /password="*password*" /connection="*ip address*" For example: "C:\Program Files\BOSCH\VMS\bin\OperatorClient.exe" /user="Admin" /password="password123" /connection="192.168.20.120" The connection parameter works with BVMS 9.0 and newer. The username and password parameters are working from BVMS 5.0 onwards. The username and password are stored as cleartext in the target of the shortcut, which could be considered a security risk.
    View full article
    ‎08-26-2019 08:34 AM
    The attached document describes how the GDPR impacts video surveillance systems and how BVMS can be configured to function in a GDPR compliant organization.
    View full article
    ‎08-27-2018 12:05 PM
    RTSP and multicast streaming
    View full article
    ‎03-02-2020 11:43 AM
    CPP6 minimum FW release changes to version 7.10
    View full article
    ‎09-16-2019 07:34 AM
    Trying out the BVMS Lite is easy! Download BVMS Lite from the downloadstore and use the quick installation guide to set-up the system. BVMS Lite contains 8 video channels, 2 workstations, 1 DVR, 2 keyboards, and 1 intrusion panel and can be used without a time limit. BVMS Lite can be expanded to 42 channels using license extensions. A step-by-step instruction on how to install the BVMS Lite license can also be found as an attachment to this page.
    View full article
    ‎10-22-2018 05:03 PM
    Learn how to design a network on which BVMS can run comfortably.
    View full article
    ‎08-08-2018 11:06 AM
    Want to know how flexible BVMS can assign streaming profiles to cameras?
    View full article
    100% helpful (3/3)
    ‎04-03-2020 03:41 PM
    Which Bosch encoders and decoders are compatible with BVMS? Up until some years ago, new released cameras, encoders, domes and decoders that are introduced into market after a BVMS release could not be connected to an existing BVMS version because these cameras where not known to the BVMS. In the BVMS 4.5.1, a new concept was introduced. This concept treats Bosch video encoders and decoders as generic devices, and automatically recognizes specific device functionality (for example the number of streams, relays and inputs). Based on this information the, at that time, unknown device is added to the system and can be used by the operator. The attached document provides a detailed description of this functionality.
    View full article
    100% helpful (1/1)
    ‎05-24-2018 11:57 AM
    Review on which ports are used for remote viewing.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist