Bosch Building Technologies

    cancel
    Showing results for 
    Search instead for 
    Did you mean: 

    Security: Video

    Sort by:
    ‎05-21-2018 08:33 PM
    Connections and programming for VIP X1XF and VG5 600 Dome.
    View full article
    ‎05-21-2018 08:31 PM
    Related Products DiBos version 8.0 to 8.7 BRS version 8.8 and later   Question How to configure LDAP in DiBos / BRS?   Answer See attached 8 screenshots which guide through the LDAP configuration. Known restrictions on the AD: - users and user groups must be located in the same directory in the AD - DiBos / BRS supports max. 1000 user groups in the AD - Comma separated user (ex. User, John) are not supported.
    View full article
    ‎05-21-2018 08:30 PM
    Related Products DVR 700 series BVIP device   Question Why does Divar 700 change the settings of 2nd stream, even though only 1st stream is configured in the DVR?   Answer Divar 700 uses the concept where it assumes to be the (master) device to have control over the cameras and their streams. Stream 1 is always set to profile 1 Stream 2 is always set to profile 2 Only one command is sent from DVR to set both stream 1&2 So please configure profile 2 in the wanted way to be used with stream 2.
    View full article
    ‎05-21-2018 08:30 PM
    Related Products VIPXD (Audio Version)   Question Why there is NO sound from a loudspeaker connected to a VIPXD SPK port?   Answer The RTC_AUDIO_LOUDSPEAKER_ON_OFF flag is not activated. This flag can be set manually by using this CGI command: http://160.10.x.x/rcp.xml?command=0x09be&type=F_FLAG&payload=1&direction=WRITE&num=1 Replace 160.10.x.x by your VIPXD IP address.
    View full article
    ‎05-21-2018 08:16 PM
    Related Products VRM Question Can I import Direct-to-iSCSI recordings into VRM? Answer No. iSCSI arrays used in Direct-to-iSCSI recording mode must be formatted when imported into VRM.
    View full article
    ‎05-18-2018 07:48 PM
    Related Products Bosch Video Client (BVC) Question Where can I find my stored recordings?   Answer Default path of the recordings is set as: C:\Documents and Setting\Admin\My Documents\Bosch\Video Client\Recordings This path can be changed in the configuration manager under the tab System > Applications > Video Client > Application > Manual Recording
    View full article
    100% helpful (2/2)
    ‎05-18-2018 01:49 PM
    Related Products All IP encoders Answer Copy/Paste the selection below to your alarm task editor and save. This script will make your encoder trip relay 1 only when IVA rule #1 alarm is active. // Set TempState to monostable mode, 5 seconds OperationMode monostable := { High(50) }; TempState(1) := monostable; if (VCARule(1,1)) then TempState(1) :=true; if (TempState(1)) then Relay(1) :=true else Relay(1) :=false;
    View full article
    100% helpful (1/1)
    ‎05-18-2018 01:41 PM
    Related Products All IP encoders   Answer Copy/Paste this example into the alarm task editor and save.  See comments below for more details, annotated by //. // Settings for JPEG posting JpegPosting PicPosting := { IP( "put ftp FQDN servername or IP here" ) Login( "anonymous" ) Password( "anonymous" ) Format( Large ) FileName( "Snap" ) Suffix( Date ) Camera( All ) }; // Define Operation Mode to periodic, 15min low and 0.1 second high OperationMode periodic := { Low(18000) High(1) }; //define logic TempState(1):=periodic; if(true) then TempState(1); if (TempState(1)) then PicPosting;
    View full article
    ‎05-18-2018 01:39 PM
    Related Products Bosch encoders Answer Place this in the alarm task editor and save it.  Please read the comments for more details.  They are noted below by //. //Define weekly timer from Monday to Sunday from 7am to 9pm Timer weekly := {TimeBegin(07:00) TimeEnd(21:00) DayBegin(Mo) DayEnd(Su) }; //define what is to be recorded Recording recording:= { Camera(All) }; // Define Operation Mode to periodic, 1 sec low 30 min high OperationMode periodic := { Low(10) High(18000) }; TempState(1):=periodic; //define recording timer OperationMode monostable := {High(50)}; TempState(2):=monostable; //Turn on recording timer if (IsActivated(weekly)) then TempState(1) := true; if (TempState(1)) then TempState(2) := true; if (TempState(2)) then recording else Stop(recording);
    View full article
    ‎05-18-2018 01:23 PM
    How many streams can use the BP+ profile?
    View full article
    ‎05-18-2018 11:58 AM
    Configure a singe mode VIF on NetApp array.
    View full article
    ‎05-18-2018 10:53 AM
    Restrictions of VRM Configuration utility pre-installed on DLA
    View full article
    ‎05-16-2018 09:24 PM
    Related Products Bosch Recording Station Video Jet X Series BRS   Question Is it possible to control an AutoDome connected to VideoJet X Series via Bilinx?   Answer In BRS 8.8.1 Bilinx over Encoder only works for devices connected via VSDKPluginModule. Current supported devices are VIP-X1600-XFM4B and VIP-X1XF. VideoJet X series are connected per default via VCSModule, which does not support Bilinx communication. To be able to control Bilinx devices on VideoJet X series please configure the following work around: 1. In BRS Configuration > IP Cameras and encoders > Scan network (VideoJetX is found) and add VideoJetX device to BRS 2. Click VideoJetX and click Edit 3. In tab General settings select Device Type BVIP H.264 4. In tab Dome settings mark Activate and select Connection Bilinx/IP Dome Now the AutoDome can be controlled via Bilinx. Note: Due to performance reasons do not change the encoder stream from MPEG-4 SH++ to H.264 streaming! Only change the device type in BRS.
    View full article
    ‎05-16-2018 09:22 PM
    Related Products DHR 700 series DNR 700 series H.264 SD IP cameras   Question How can I record SD H.264 cameras in Main Profile (MP)?   Answer For the IP cameras disable the setting "SD display on local monitor required" - then the camera is disabled for live viewing but it is recorded in MP and can been seen via the BVC.
    View full article
    ‎05-16-2018 09:41 AM
    Bosch ST has sold the HP Workstations and the HP Enterprise Servers  and is responsible to provide the required Service & Support for these products regardless of the SLA in place with HP. Therefore, the customer always will contact the Bosch After Sales organization in case of any problems encountered with one of these products. The customer must never been told to contact HP or HPE directly if he seeks support from Bosch. In this solution article a questionnaire for a first basic analysis of a reported issue is described. This checklist is intended to help to identify and resolve known issues immediately and to collect relevant data in case of an unknown issue.  
    View full article
    ‎05-16-2018 09:39 AM
    This article describes how to deploy Microsoft Security Updates on a BRS Appliance
    View full article
    ‎05-16-2018 09:34 AM
    After changing the resolution of monitor to UHD (3840*2160), the attached monitors results always black.
    View full article
    ‎05-16-2018 09:31 AM
    Product Security Advisory: Meltdown and Spectre vulnerability in Common Product Platforms (CPP)
    View full article
    100% helpful (1/1)
    ‎05-14-2018 11:09 AM
    Network switch has port security on and shuts down a NetApp iSCSI data port (e.g. CH3). This article is only relevant in aspects of network security / port security where MAC addresses are analysed. Some network security applications are capable of sniffing network packets thoroughly enough to pick up MAC addresses on E-Series Controller ports that are not seen in the Storage Array Profile data.
    View full article
    ‎05-14-2018 10:56 AM
    Memory leak on a Divar IP 7000 R2 triggered by Catalyst Control Center.
    View full article
    Top Contributors
    Icon--AD-black-48x48Icon--address-consumer-data-black-48x48Icon--appointment-black-48x48Icon--back-left-black-48x48Icon--calendar-black-48x48Icon--center-alignedIcon--Checkbox-checkIcon--clock-black-48x48Icon--close-black-48x48Icon--compare-black-48x48Icon--confirmation-black-48x48Icon--dealer-details-black-48x48Icon--delete-black-48x48Icon--delivery-black-48x48Icon--down-black-48x48Icon--download-black-48x48Ic-OverlayAlertIcon--externallink-black-48x48Icon-Filledforward-right_adjustedIcon--grid-view-black-48x48IC_gd_Check-Circle170821_Icons_Community170823_Bosch_Icons170823_Bosch_Icons170821_Icons_CommunityIC-logout170821_Icons_Community170825_Bosch_Icons170821_Icons_CommunityIC-shopping-cart2170821_Icons_CommunityIC-upIC_UserIcon--imageIcon--info-i-black-48x48Icon--left-alignedIcon--Less-minimize-black-48x48Icon-FilledIcon--List-Check-grennIcon--List-Check-blackIcon--List-Cross-blackIcon--list-view-mobile-black-48x48Icon--list-view-black-48x48Icon--More-Maximize-black-48x48Icon--my-product-black-48x48Icon--newsletter-black-48x48Icon--payment-black-48x48Icon--print-black-48x48Icon--promotion-black-48x48Icon--registration-black-48x48Icon--Reset-black-48x48Icon--right-alignedshare-circle1Icon--share-black-48x48Icon--shopping-bag-black-48x48Icon-shopping-cartIcon--start-play-black-48x48Icon--store-locator-black-48x48Ic-OverlayAlertIcon--summary-black-48x48tumblrIcon-FilledvineIc-OverlayAlertwhishlist